Hi all,
Really appreciate some feedback if this will be workable, I have already started a thread for this build but didn't realise this parts list section existed and when I was reviewing realised I had made a bunch more mistakes e.g expecting the NB2 chassis discs could accommodate a prewired NB2 board with harness so if one or more of you fine people could give me the thumbs up or down that would be great.
Sound system setup:
1 x NB2 board http://www.thecustomsabershop.com/Na...e-V2-P806.aspx
1 x JST Female connector 24AWG Red/Black http://www.thecustomsabershop.com/JS...lack-P964.aspx
1 x MWS Recharge Port http://www.thecustomsabershop.com/MW...Port-P877.aspx
1 x JST Male connector 24AWG Red/Black http://www.thecustomsabershop.com/JS...lack-P963.aspx
1 x Kill plug style 2 http://www.thecustomsabershop.com/Ki...le-2-P570.aspx (already ordered)
1 X Panasonic Battery (sourced elsewhere due to being in Australia)
Does this wiring idea look correct?
1. NB2 TO RECHARGE PORT TO BATTERY.JPG
High powered LED:
1 X JST Female connector 24AWG Blue/White http://www.thecustomsabershop.com/JS...hite-P958.aspx
1 X 1ohm 2w resistor http://www.thecustomsabershop.com/1o...istor-P21.aspx
1 X Rebel Star LED & MHSV1 Heatsink Module http://www.thecustomsabershop.com/Re...dule-P653.aspx (Lime Green already ordered)
Have I understood the wiring requirement?
2. NB2 TO RESISTOR TO HIGH POWER LED.JPG
Switch setup (with lit activation switch when kill key is removed):
1 X MWS Short Momentary 16mm AV Switch - Nickel http://www.thecustomsabershop.com/MW...ckel-P878.aspx
2 X JST Female connector 24AWG Red/Black http://www.thecustomsabershop.com/JS...lack-P964.aspx
Thanks GJ updating wiring!
Detachable speaker setup:
1 X JST Male connector 26AWG Green http://www.thecustomsabershop.com/JS...reen-P952.aspx
1 X JST Female connector 26AWG Green http://www.thecustomsabershop.com/JS...reen-P956.aspx
1 X Premium 28mm Speaker http://www.thecustomsabershop.com/Pr...eaker-P77.aspx (already ordered)
4. NB2 TO SPEAKER.JPG
Chassis setup, particularly interested if I can use a "Acrylic Chassis Disc 2 hole to 3 hole adapter" as the end piece of my chassis to but up against the activation switch in the hilt?
2 x Stainless 4-40 all thread http://www.thecustomsabershop.com/St...read-P770.aspx
1 x Acrylic Chassis Disc for NB and 18500/18650 pack - S3 http://www.thecustomsabershop.com/Ac...k-S3-P813.aspx
Assorted OD spacers (ordered 4 x each of: 2" Aluminum 3/16" OD spacer, 1.5" Aluminum 3/16" OD spacer, 1" Aluminum 3/16" OD spacer, 3/4" Aluminum 3/16" OD spacer & 1/2" Aluminum 3/16" OD spacer (Clear))
1 x Acrylic Chassis Disc 2 hole to 3 hole adapter - S9 http://www.thecustomsabershop.com/Ac...r-S9-P773.aspx
1 x MHS speaker mount V4 - For 28mm Speakers http://www.thecustomsabershop.com/MH...kers-P661.aspx
After reading other answers to my questions about how to pass wires past chassis pieces I hope it's possible to make cut outs in the NB2 chassis discs to allow speaker wires and recharge port wires past?
Bookmarks