-
Build/Parts List Check: MHS CFX In-Hilt RGB Tri Cree LED
The time has come!
Dad and I decided to start a new Father-Son project this holiday, and we settled on building lightsabers! This will be our first lightsaber build ever. I know it's advised to start super simple for a first build, but as this is a Father-Son project, and my dad is extremely well versed in electronics and mechanical know-how, we decided to go big. Below is a list of parts, the MHS Builder design, and a diagram depicting the chassis and wiring. A note on the chassis: I'm using a NB sized chassis for the CFX, as the CF doesn't fit, and I saw a thread here that showed how to modify a NB style chassis slot to accommodate a CFX board. Thread here
Parts:
Crystal Focus Sound Module X
x1
MHSV1 Blade Holder Style 17
MHS Flat Style Heat Sink
x1
MPS Pommel style 3 v2
x1
Hilt Style 5 (7" Fluted double female threaded connector)
x1
MHS choke style 3
x1
MHSv1 speaker mount Style 5 - For 28mm Speakers
x1
Saber Essentials 28mm Stealth V2 Speaker
x1
Switchcraft 2.1mm Power Jack
x1
18deg Tri-Rebel/Cree Star Lens
x1
Star thermal tape pad - Tri LED
x2
Red/Green/Royal Blue Cree XP-E2 CopperNova
x1
Panasonic Li-Ion 18650 3.7V 3400mAh PCB Protected Rechargeable Battery
x1
MPS Insert style 1
x1
MPS Clip
x2
12mm Anti Vandal Momentary Blue Ring Switch
x2
Machine recessed 12mm AV switch hole
location: Power and Aux for CFX. Wherever is best in the smooth section of the hilt, closer to the choke. In line with blade.
x2
82ohm 1/4w resistor
x6
.3ohm 1w resistor
x6
1.2ohm 3w resistor
x6
28 gauge wire (sold by the foot) (Black)
x3
28 gauge wire (sold by the foot) (White)
x3
28 gauge wire (sold by the foot) (Red)
x3
28 gauge wire (sold by the foot) (Green)
x3
Kill plug style 5 - Black
x1
Stainless 4-40 all thread
x4
Stainless Steel 4-40 Hex nut
x10
Chassis Disc style 5
x1
Acrylic Chassis Disc for Recharge Port - S8 (Black)
x2
Acrylic Chassis Disc for NB/Pico and 18500/18650 pack - S3 (Black)
x2
1/16" Heatshrink tubing
x3
3/32" Heatshrink tubing
x3
1/8" Heatshrink tubing
x3
3/16" Heatshrink tubing
x3
1" Anodized Black Aluminum 3/16" OD spacer
x2
1.5" Anodized Black Aluminum 3/16" OD spacer
x2
1/2" Anodized Black Aluminum 3/16" OD spacer
x2
1/4" Anodized Black Aluminum 3/16" OD spacer
x2
3/4" Anodized Black Aluminum 3/16" OD spacer
x2
Drill & Tap Hole (8-32)
location: This is for the Blade Retention Screw, so wherever is best
8-32 x 3/8" Stainless Steel thumb screw
First Saber.jpg
MHS Build Diagrams.jpg
Let us know if this all checks out, any recommendations, or additions you can think of! Thanks so much!
MTFBWY
EDIT: Diagrams seemed small when posting so here's another way to view it: https://imgur.com/a/RCEALjy
Last edited by Valcarion; 01-07-2020 at 05:07 PM.
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Bookmarks