-
It didn't work. Here is a shot of how I set up the banks. Sound Font Folder.jpg Banks 1-3 Are the Default Light, Grey, and Dark Meat Bank4-6 will be my new sound fonts. I copied banks 1-3 and then changed the names of them to bank4-6. Then I copied and pasted each new bank into their new folders keeping the config file. I then formatted the SD card to erase it. I dragged the new configuration into the SD card. At this point it should cycle up on my saber when I go through the banks but it only does the original three. When I added the new config to the SD card it went from 3.68 GB to only 3.66GB. I have followed everyones advice, watched Madcows video on Saberfont.com, and read the manual over and over. what am I doing wrong
-
Jedi Council Member
Open the revisions file, and make sure it says Prizm 3.5 in it.
TCSS MODERATOR
All n00bs READ these first (PLEASE)!!!:
1. Forum Guidelines
2. FJK’s “Down and Dirty” guide to Ohm’s Law
"Yeah, yeah, I've heard it all before... you want blindingly bright, super loud, running 1138 blinkies off of the cheapest sound card you can find AND you want all of it to run on a battery the size of a dime, and run for a very, VERY long time. That one cracks me up every time..."
My email: fjk_tcss@yahoo.com
-
Here is what the revision file says:
Petit Crouton 3.5 by Plecter Labs
PRIZM EDITION
Plecterlabs - Props electronics
http://www.plecterlabs.com
erv@plecterlabs.com
Default Package featuring fonts Light Meat (bank1) and Dark Meat (bank3) by Eastern57
and Grey Meat (bank2) by Sekrogue
For more sound fonts for your beloved saber sound card:
!!!!!!!!!!!!!!! - please visit www.saberfont.com - !!!!!!!!!!!!!!!!!!!!
The Override:
## Override File
vol=2
beep=6
valsnd=1
switch=2
offp=0
offd=0
lc=400
hs=220
ls=50
i=30
swing=200
clash=150
lockup=150
## Color profiles
color0=0,17,994
fcolor0=0,880,0
color1=0,682,0
fcolor1=966,17,0
color2=0,795,596
fcolor2=0,795,0
color3=0,830,400
fcolor3=700,940,0
color4=840,0,630
fcolor4=0,0,940
color5=940,430,0
fcolor5=0,940,0
color6=740,930,0
fcolor6=0,740,600
color7=0,0,0
fcolor7=0,0,0
color8=0,0,0
fcolor8=0,0,0
color9=0,0,0
fcolor9=0,0,0
And the Prefs:
// User Prefs - Do no modify
bank=00
color0=00
color1=01
color2=02
That is everything on the SD card except for the actual sound banks
-
I am having this exact problem also.... Haven't figured it out yet.
-
I sent a note to erv at Plecter labs and though he's on vacation right now he asked me to recontact him in mid august. He going to check the firmware on the boards.
-
Jedi Council Member
Yeah, I think that might be your problem - that's why I asked about the contents of the revision files.
TCSS MODERATOR
All n00bs READ these first (PLEASE)!!!:
1. Forum Guidelines
2. FJK’s “Down and Dirty” guide to Ohm’s Law
"Yeah, yeah, I've heard it all before... you want blindingly bright, super loud, running 1138 blinkies off of the cheapest sound card you can find AND you want all of it to run on a battery the size of a dime, and run for a very, VERY long time. That one cracks me up every time..."
My email: fjk_tcss@yahoo.com
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Bookmarks