Search:

Type: Posts; User: Ka'getsu

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    3,197

    Actually grey if you have an additional 15...

    Actually grey if you have an additional 15 dollars to spare you could buy an ultimate FX saber and gut it for it's board, they're a bit better than the el cheapo boards mainly because the blade...
  2. Yep that would be the one. And as far as the...

    Yep that would be the one. And as far as the rechargeable batteries running the electronics you shouldn't have a problem with it, but you should make sure that you wire a tip 42 transistor
    to the...
  3. Replies
    2
    Views
    3,429

    Well Guardian almost all saber blades are made...

    Well Guardian almost all saber blades are made out of polycarbonate (3/4-1" thin or thick walled) as far as brightness goes, it really depends on what you use to diffuse
    the light with, and the...
  4. I don't know.... It sort of looks green to me

    I don't know.... It sort of looks green to me
  5. Replies
    5
    Views
    3,442

    How badly did you break it? If It's not too bad,...

    How badly did you break it? If It's not too bad, you might be able to repair it.
    And just FYI it's really bad etiquette to solicit sales or trades on these forums
    (if that's what you're trying to...
  6. Replies
    1
    Views
    3,953

    hey Radioman... a quick answer to you r second...

    hey Radioman... a quick answer to you r second question You can go over to this thread http://forums.thecustomsabershop.com/showthread.php?675-MR-Conversions&highlight=saber+conversions and see...
  7. Replies
    6
    Views
    3,346

    They most likely will (have flux cored solder)...

    They most likely will (have flux cored solder) you could also get away with using rosin cored solder. Also if you use flux cored, be sure to clean the joint afterwards to prevent it from rusting
  8. Replies
    10
    Views
    7,150

    In a "Bifurcating" saber core the crystals are...

    In a "Bifurcating" saber core the crystals are oriented end to end, I believe

    Hope that helps.

    Cheers :)
  9. Replies
    4
    Views
    5,256

    I agree with havoc.. nice build. i do have one...

    I agree with havoc.. nice build. i do have one question though, what are you going to use for a heatsink? If you're wanting to save space you can use a 3/4" copper endcap as seen in this tutorial...
  10. Replies
    2
    Views
    3,042

    Yeah they do, you can use them for just about any...

    Yeah they do, you can use them for just about any 3 wat. led, and with a little modification (1" section of 3/4" id. copper pipe, and 1" section of 3/4" aluminum rod along with the endcap. Wrap the...
  11. Replies
    12
    Views
    9,190

    Tim is usually pretty good at geting back to...

    Tim is usually pretty good at geting back to people quickly, so you can expect a response within a day or two
  12. Replies
    16
    Views
    11,797

    Yeah... What Jenny and Havoc said:)

    Yeah... What Jenny and Havoc said:)
  13. Replies
    7
    Views
    4,634

    i have to agree with Ripper that's really nice...

    i have to agree with Ripper that's really nice shroud work. hope to see it completed soon.

    Cheers :)

    -K-
  14. Replies
    2
    Views
    2,903

    I like the saber, and I'd also like to say that...

    I like the saber, and I'd also like to say that you did a really good job of explaining how you built the chassis for it. quick, simple and easy to follow
    keep up the good work

    cheers

    Ka'ge
  15. Replies
    3
    Views
    2,250

    Nice saber, I really like the shroud work, must...

    Nice saber, I really like the shroud work, must have taken a fair bit of quality dremmel time.
  16. Replies
    10
    Views
    5,293

    nicely done saber.... looks really comfortable to...

    nicely done saber.... looks really comfortable to wield
  17. I do have to say. that saber is coming together...

    I do have to say. that saber is coming together rather nicely :)
  18. Replies
    4
    Views
    2,656

    I personally like the emitter, you could however...

    I personally like the emitter, you could however cut the inner part of it at a 30 degree angle to give it a little more character. Anyhow it looks like it's going to be a nice looking saber...
  19. Replies
    13
    Views
    8,238

    http://forums.thecustomsabershop.com/forumdisplay....

    http://forums.thecustomsabershop.com/forumdisplay.php?15-MR-and-Hasbro-to-luxeon-3w-conversions, and invest in a drill & tap set for the thumb hole screw, as far as i know the conversion kits that...
  20. Replies
    3
    Views
    2,008

    Both types should be fine, my personal preference...

    Both types should be fine, my personal preference would be the 16/0.2 mm. since it'll give you a bit more leeway, 'ccause i believe that an MR board can push up to 1500 ma (1.5 amps) if my memory...
  21. yep... i agree with sunrider, radio shack $2.00...

    yep... i agree with sunrider, radio shack $2.00 or less
  22. @Garrek I noticed that you said that you were...

    @Garrek I noticed that you said that you were going to run your led dies in series.... Depending on the power solution you're going to use, you might want to think about running them in parallel,...
  23. Replies
    8
    Views
    4,205

    Nice... I'm digging on the shroud word and your...

    Nice... I'm digging on the shroud word and your design aesthetic, really solid work :)
  24. Replies
    137
    Views
    80,323

    @ Jenny, he's using a Crystal Focus v5 LS. as a...

    @ Jenny, he's using a Crystal Focus v5 LS. as a sound/ led driver, for the most part it can drive the main led, accent led's play movie accurate sound fonts and make breakfast for you. (not sure...
  25. Replies
    3
    Views
    2,467

    looks good so far, I know that I'd be happy with...

    looks good so far, I know that I'd be happy with it if I was your customer :)
Results 1 to 25 of 81
Page 1 of 4 1 2 3 4