I haven't posted in forever because life changed for me professionally and in where I spend my spare time. For anyone that remembers him though, Don Close (Do-Clo) passed this morning. He's been...
Type: Posts; User: xwingband
I haven't posted in forever because life changed for me professionally and in where I spend my spare time. For anyone that remembers him though, Don Close (Do-Clo) passed this morning. He's been...
A drill press should not used for milling functions. You might get away with it for a bit, but the taper of the chuck and bearings are not made for milling. It will eventually throw the bit and/or...
Yup, January 2010. Ridiculously cold morning for Florida (30's) I went out on my still new to me motorcycle. I lost traction on the back wheel going too hard up a hill and I ended up rubber side...
Sort of... I lurk every few weeks. I had a really bad broken ankle at the start of graduate school that took me out. Grad school and now my professional life (I'm a licensed Architect now) means I...
There's nothing different with the newer LEDs if you're running it straight from the MR board. You likely just broke the strip and you can run it just fine from the board. For your budget there's...
1) Depends on how you're driving them. Theoretically whatever you can fit and you may be able to put in whatever you have on hand.
2) Yes, typically we cut of the driver to isolate the batteries....
Beaten to a degree but I'm typing slow...
You're understanding is incorrect... it's actually almost reversed.
In parallel you need double the amperage, but the same voltage. In series you need...
I would strongly recommend that last part from the manual for getting a resistor value of the motor. If you have a power supply there's no reason you shouldn't try to figure out the forward voltage...
Indeed as in "Yes, it works."
I'm doing it right now. In addition to TCSS parts I grabbed some nylon parts from my hardware store. A 1.375" washer works for the inside of a Graflex. So not only...
Should be good now on the PM box.
I'll post progress tomorrow. I drilled and tapped a bunch of holes today... some visible and some not, like holding in the pommel and heatsink. I decided to use...
Today got really side tracked... good thing but I didn't do anything with the saber.
ARKM, shoot me a message here. I have a few and with any luck they may have been yours and I spaced on while...
Yeah, I was just poking my head over there. I'll probably post soonish there. I did look around to see if someone had more posts than me at this point... took JLo a few years but it appears she has!
Well... hello people! I haven't touched a lightsaber in years now. I occasionally take out my built ones to show but I haven't built one in years. Some of you may remember I broke my ankle three...
Yeah, they were a direct tap to the power and amped the PWM from those outputs. I wasn't aware of a limit, but I'm not surprised as it's probably the practical limit of the components.
Also... TCSS Squadrons. They don't mean much. I used to have a "Red Leader" sig back in the day and it was cool to say who would be the others. We started to fill them out and whatever.
So...
I LOL'ed. Before I read it I realized it was a razor head.
Behold the power of SCHICK!
Green/Blue/White Rebels can all go up to 1A just fine. It's within their specs, but for some reason Luxeon publishes them at 700mA.
I've found no reason to go to more, but they don't make that...
Tritium is highly regulated. Not nearly as bright as people may want too. It's used a lot for gun sights. It'll also "die" in a few years (less than a decade).
Late, but welcome to my world... it will get to all of you eventually. Then you'll just stop caring.
As one of the oldest members, I've seem it come and go. Personally I haven't been posting...
So the goal is to not regulate under 12V and regulate above that?
Yup, Ultra stopped using contact paper when he started ordering from Tim.
I use mylar also. Why? I find a full mirror doesn't light up the tip enough. Cutting a smaller one helps but IMO it...
Not discussed so much as offered and tried I'd say. Erv has a by request system that sends the triggers directly to a wireless system for playback through your standard PA/large speaker systems.
...
I still don't understand the question... or what warranted the response. That post was so vague I don't know how to even respond.
Do you have calipers? that has to be a rough guess because 3mm is very visibly too large. It takes little to not fit well. Sanding is not unusual though. Tends to be larger with the thin tubes...
NAND's are pretty easy... I'd just go with that.