This is what I have so far.
In regards to Li-ion batteries, how snug of a hold is "too much" and how much is "too loose"?
My chassis allows the battery to go in smoothly for each of my batteries...
Type: Posts; User: Old Stormtrooper
This is what I have so far.
In regards to Li-ion batteries, how snug of a hold is "too much" and how much is "too loose"?
My chassis allows the battery to go in smoothly for each of my batteries...
View down the Emitter (AKA: Luke Skywalker's view :o ):
https://imagizer.imageshack.com/v2/xq90/923/phmrVj.jpg
Side by side, Hilt and Chassis:
https://imagizer.imageshack.com/v2/xq90/922/BiUBe8.jpg
This is how I intend to access internals to replace batteries/connect to RICE/swap out MicroSD cards.
Pommel w/pommel insert installed:
https://imagizer.imageshack.com/v2/xq90/922/EkPepn.jpg
Inserting the Chassis into the final MHS piece:
https://imagizer.imageshack.com/v2/xq90/922/pIR2EN.jpg
Showing closer how the latch secures with tension:
https://imagizer.imageshack.com/v2/xq90/924/Y3Qigg.jpg
Latching the gate:
https://imagizer.imageshack.com/v2/xq90/924/gpnsAV.jpg
I goes in easily:
https://imagizer.imageshack.com/v2/xq90/924/198WY4.jpg
Showing battery clearance:
https://imagizer.imageshack.com/v2/xq90/923/YYSI6k.jpg
Chassis with the gate open:
https://imagizer.imageshack.com/v2/xq90/924/xhaXgg.jpg
This is my Chassis.
https://imagizer.imageshack.com/v2/xq90/922/Gp28on.jpg
Hello All! I'm starting this thread to document my first build (all TCSS) and get feedback, hints, comments and advise as I go through this endeavor. The overall length is under 11", so I'm diving in...
Thanks. I've always liked the chamfered cutout look and tried to keep it out of the way of the pixel base. When I get it finished, I'll post pics and let you know if I was successful.
It took a while, but well worth the wait! (Real life getting in the way, others buying out the stock before I could order, etc. It all added up.) I had a specific concept in my head. This thing is...
and should I be running dual (or more) wires from the Prizm board to disperse the heat and load as well?
If using a 3.7v 15a battery, what is the preferred gage and how many wires for the 7 pin and 11 pin connecter from a Prizm?
This is actually why I posed the question. The choke portion (which is actually a separate piece), looked significantly smaller than almost all of the other MHS parts for wall thickness. I figured...
Yes, this is what I was looking for. Thank You! very much.
For #3, I was trying to ask for "12 o'clock position to 3 o'clock to 6 o'clock to 9 o'clock back to 12 o'clock position" or "360 degrees like screwing the threaded parts together direction" count,...
Is the Ribbed grooved / Choke Combo https://www.thecustomsabershop.com/Ribbed-grooved-Choke-Combo-P524.aspx tough enough for dueling?
Also, does anyone have the dimensions of the "flats" on the...
And..... crap. Thanks for saving me some serious ranting and throwing things. I saw the four leads and got ahead of myself.
Thanks. I may end up getting one from the Shop as back-up. I found essentially a "kit" version of the 5mm LED/switch (another site, forgive me) and will likely try to install a RGB LED from the Shop...
I believe the 20mA DynaOhm would work perfectly, however, would a different resistor get me more of an "Amber" color? Does this type of LED work that way?
OR, could I "rebuild" the switch with a...
Thanks. Not what I was hoping for but at least I know I wasn't missing something.
NeoPixel & CF8 - are they compatible? I started gathering components for a build I have in mind and had to put it on hold due to real life. Now that I am getting back to it, I find myself wanting to...