I'm only running one blade, looking at the diagram I'll only be using data 1. I have a LED momentary switch for on/off which I have the resistor for that already. So, I should be good?
Type: Posts; User: Echo4Delta
I'm only running one blade, looking at the diagram I'll only be using data 1. I have a LED momentary switch for on/off which I have the resistor for that already. So, I should be good?
You think this is the bad boy I should get?
DM Keeppower Li-Ion 21700 3.7V 15A 5000mAh PCB Protected Rechargeable Battery
...
I have the LIon Battery from my original build over 9 years ago. Still holds a charge.
3.7v/2400mAh
PAN18650P
Oh, and do I have to worry about resistors and such or does the Profeeboard come with all them built in?
So the rest of this will turn my V1 build into a Pixel?
And thanks for the wire tip too!
I built my custom lightsaber from this store around 10 years ago. Its time for an upgrade and all the help is appreciated.
I currently have a MHS V1 setup with a Nano Biscotte V2 and a tri-rebel...
http://www.zentai-zentai.com/dark-brown-morph-body-suit-full-body-uni***-lycra-zentai-suits-products-495.html#.U0SIj1dNsbo
999599969997
Yes, royal blue with Nano Biscotte and Blue ring momentary
99% Done! Just need a few teaks on the boots and wiring and that's about it. Hope you all took away something form this 'tutorial'. Hit me up with messages if you have questions. Thanks for checking...
Ebay purchased pouches. Military-spec compass pouch...
They were too big so, I just glued the edges as shown below...
991299139914
Now, this is a bit advanced for costuming, but considering its on a forum that deals with a lot of electronics...
Let there be light...
98999900990199029903
Yea, I've done the thigh pieces like that with my Iron Patriot armor. I'm gonna try the Velcro first because they feel like they fit perfectly before they slide down. Nice and tight, so I'm hoping...
Okay, remember that cloak? Yea, I finished it. I simply sewed the seams together and added a hood. Well, perhaps not 'simple' Took me hours to figure out how to set the sewing machine up. And that...
The hand guards I just accented with silver and added weathering. Here is what it'll look like when it all comes together...
98779878987998809881
I realized that I would have a easier time to...
Again, I simply used layers to paint the guantlets and weathered them using black poster paint and wiped it off with a dry and then damp paper towel.
9873987498759876
Purchased some gloves from Walmart in the men's section. But, they are leather/poly fabric that I could paint with metallic sharpies to give it a metallic/sci-fi look.
Note: In the last picture...
986498659866
Here are the shin and chest sections and the overall look so far. The gauntlets and hand guards are still left to paint and Those pesky pouches.
Okay, weathering some more! I simply purchased some cheap black poster paint that is water-based. So, if you mess-up you can simply wipe off with a damp towel/napkin.
Using a small paint brush I...
The shin pieces. Remember I painted them two toned? Silver on top and nickel on the bottom.
9857985898599860
You can use the same technique to add battle damage where it would give the viewer a sense that something hit the armor and scratched off the top layer of paint exposing the armor's metal. But, be...
I repainted the chest with the nickel and decided to do a green spray instead of using a wash. It turned out pretty good, although I think I went a bit dark. But, just be aware of wind because it can...
984298439844
Simply copied the lines from the reference pics to give the thighs and cod/belt pieces detail. I plan on glazing over the metallic areas on the thighs with a satin paint layer to...
982598269827
The guantlets
98209821982298239824
On the belt I've started an accent piece and while it was still wet I balled up a piece of paper to apply scratches to dry as a 'weathered' or used armor look.