Search:

Type: Posts; User: Forgetful Jedi Knight

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds; generated 38 minute(s) ago.

  1. Ideally, you want to only remove the rear grip to...

    Ideally, you want to only remove the rear grip to either remove the battery ( if you’re using swappables) or access the SD card/USB port. That’s one (of many) reasons why placement of things like...
  2. Yes, the standard is that the resistor is ALWAYS...

    Yes, the standard is that the resistor is ALWAYS on the blade side.
  3. What Tim said. All my Neopixel builds are with...

    What Tim said. All my Neopixel builds are with the CFX. Feel free to check out the wiring video I did about 18 months ago on it. Itís in the video section.
  4. It depends on the color, but as Tim said, 30-45...

    It depends on the color, but as Tim said, 30-45 minutes would be the norm, depending on the color(s) you use.
  5. It realistically can be anywhere on the circuit....

    It realistically can be anywhere on the circuit. Iíd examine where you currently have it, and find out why itís breaking.
  6. Also, what kind of speaker are you using?

    Also, what kind of speaker are you using?
  7. Yes, however, it will take several hours to...

    Yes, however, it will take several hours to completely charge.
  8. Iíve got it Light Bringer.

    Iíve got it Light Bringer.
  9. Not likely. I would recommend you sign up to...

    Not likely. I would recommend you sign up to FX-Sabers and ask this question over there, at the board’s creator (Erv’ - Plecter Labs) has his troubleshooting section there.

    As for the colors, that...
  10. Itís highly recommended for ease of use.

    Itís highly recommended for ease of use.
  11. Where are you putting the recharge port? EDIT:...

    Where are you putting the recharge port?

    EDIT: I sent you a PM.
  12. What does this MHS saber look like?

    What does this MHS saber look like?
  13. This, with the JST attachment ...

    This, with the JST attachment

    https://www.thecustomsabershop.com/37V-148V-1Amp-Li-Ion-Smart-charger-P1180.aspx
  14. Replies
    11
    Views
    441

    Funny how that works out, huh?

    Funny how that works out, huh?
  15. Replies
    11
    Views
    441

    Well, look whoís back.

    Well, look whoís back.
  16. Replies
    2
    Views
    503

    Yes, I’m doing one now for a client, that has an...

    Yes, I’m doing one now for a client, that has an “exposed” OLED screen (NOT using the mount you have shown). And they have been done before, VV was one of the first major players to incorporate them...
  17. It doesnít matter if the ground to the switch is...

    It doesnít matter if the ground to the switch is 24 gauge. If you have the room, you can use those deans connectors. I use those (and variants of those) at certain junctures in my Neopixel builds.
  18. It gets complicated. The wires that touch the...

    It gets complicated. The wires that touch the switch (LED, signal and related grounds) donít need to be larger gauge, BUT the wires to and from the board should be where the battery (+) and (-) and...
  19. All of the above are what I mean, except the...

    All of the above are what I mean, except the switch wire. The ground to that can be a smaller gauge.
  20. 1. Yes. 2. No, you need 22 gauge for the...

    1. Yes.

    2. No, you need 22 gauge for the neopixel wires.

    3. That’s “voltage ripple”. The neopixels are trying to pull more out of your battery than it can comfortably provide, that why your...
  21. Yes, you still need the other battery.

    Yes, you still need the other battery.
  22. Yes and yes.

    Yes and yes.
  23. You have the wrong battery. You need a 15A...

    You have the wrong battery. You need a 15A battery for Neopixels.
  24. Replies
    12
    Views
    1,764

    The 11-pin just spreads the electrical load out...

    The 11-pin just spreads the electrical load out over more pins.
  25. Replies
    12
    Views
    1,764

    Yes, however, using latching switches isnít...

    Yes, however, using latching switches isnít common these days. Also you would have to change the configuration to handle a latching switch.
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4