Search:

Type: Posts; User: Forgetful Jedi Knight

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Usually the ďQONĒ parameter controls that.

    Usually the ďQONĒ parameter controls that.
  2. Replies
    2
    Views
    87

    No, the first version is the most popular and...

    No, the first version is the most popular and oldest. The second version just has a slightly smaller diameter. Thatís all.
  3. Replies
    8
    Views
    429

    Running them at 1A will be fine. The Reds you’ll...

    Running them at 1A will be fine. The Reds you’ll have to check the spec sheet. They may only be 700 mA.
  4. Replies
    8
    Views
    429

    Not only that. The battery I recommended will be...

    Not only that. The battery I recommended will be way more efficient for these setups. 7.4V batteries were better in the old days (CF 6 and below), but aren’t as great at driving “modern” setups. And...
  5. Replies
    8
    Views
    429

    It is 1A per die. You would be better off using...

    It is 1A per die. You would be better off using the 3.7V 3400 mAh battery. We normally don’t mix any type of buck puck with sound cards, resistors are used.
  6. Replies
    8
    Views
    429

    Welcome to the Forums. What card are you using?

    Welcome to the Forums. What card are you using?
  7. Is that a latching switch you are using?

    Is that a latching switch you are using?
  8. What is that black square under the white wires?...

    What is that black square under the white wires? It appears that the LED grounds go into it.
  9. You have a ground somewhere in your wiring.

    You have a ground somewhere in your wiring.
  10. The in game one and the Slothfurnace one are...

    The in game one and the Slothfurnace one are basically one and the same. He made Derelict, and he put it in the game. ;)
  11. Replies
    3
    Views
    427

    You can use the recharge port for a 7.4V battery.

    You can use the recharge port for a 7.4V battery.
  12. You should be able to.

    You should be able to.
  13. Replies
    15
    Views
    1,893

    Smoothswing files do have a different setup, itís...

    Smoothswing files do have a different setup, itís more how the card reads it IIRC.
  14. Replies
    15
    Views
    1,893

    No, it wonít work on NBís. The compatibility with...

    No, it wonít work on NBís. The compatibility with CF is more for non smoothswing fonts.
  15. Itís been done before using small Switch 22...

    Itís been done before using small Switch 22 (domed switch). No I donít have any pics handy, but theyíre around, somewhere.
  16. Replies
    8
    Views
    990

    For what you have planned, it looks fine.

    For what you have planned, it looks fine.
  17. Older boards like that DO NOT support Smooth...

    Older boards like that DO NOT support Smooth Swing. Thatís why youíre having issues.
  18. Replies
    8
    Views
    990

    Thatís the main thing. You might need other...

    Thatís the main thing. You might need other resistors, but until you fix the picture, I canít see it well enough to tell you. 😉
  19. Replies
    8
    Views
    990

    To post pics, usually you host it offsite, and...

    To post pics, usually you host it offsite, and post a BBCode link.

    For the Neopixel blade, the resistor goes on the blade side PCB
  20. No. I believe itís under Crystal Focus Sound...

    No. I believe itís under Crystal Focus Sound Fonts.
  21. You can go through the archives on Plecter Labs...

    You can go through the archives on Plecter Labs website and download the SD card contents there.
  22. Welcome to the forums. Offhand Iíd say the...

    Welcome to the forums.

    Offhand Iíd say the battery amperage was insufficient. You need a 15A battery to run a setup like that.

    In case you werenít aware, these forums are attached to a site...
  23. Replies
    7
    Views
    1,099

    Iíd have to research the various wiring diagrams,...

    Iíd have to research the various wiring diagrams, but I donít think so. You add the resistor to help protect the LEDs themselves, and also, a 50 cent resistor is way cheaper than replacing a GGW...
  24. Replies
    7
    Views
    1,099

    Each LED should have its own resistor.

    Each LED should have its own resistor.
  25. You likely have a switch issue, or you have it...

    You likely have a switch issue, or you have it set so that you have to hold the switch down for a couple of seconds to turn off.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4