Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11

Thread: my saber, hopefully ordering soon!

  1. #1
    Jedi Padawan astromech_kuhns's Avatar
    Join Date
    Aug 2008
    Location
    Korriban (sith temple)
    Posts
    637

    Default my saber, hopefully ordering soon!

    ok so hopefully ill order once the emmiters com in stock again.

    heres my blade, electronics and hilt as well as the pieces ill order.

    covertech clip
    covertech button
    8-32 socket head

    that will make for my clip adn covertech button attached to my hilt and the screw its using to attach it to the hilt.

    LED "Corbin style" Battle blade 1" OD (36 inches)

    this will be my blade.

    4AAA battery holder
    luxIII star
    push on/off switch (black button)
    2.2ohm 5w resistor (will later get changed to driver board)
    luxIII/V lens holder
    5 degree viewing angle

    that will be my electronics system for my saber till i add a driver board adn sound.


    1.5 x 12" sink tube
    1-3/8" Chrome end cap
    8-32 x 1/2" thumb screw
    LED emitter style 1
    8-32 x 1/4" button head screw (4 of them)
    1.5 sink tube/MHS adapter.



    the whole thing will cost me $100.00

    any problems you see? and suggestions?

    **list has been updated with corections**
    Last edited by astromech_kuhns; 12-01-2008 at 11:21 PM.
    if you are new these links will get you started

    tutorial on ohms law!!!
    the saber building dictionary-a dictionary with basically everything about sabers!
    thread index-this is the thread index!
    the basic saber building tutorial-tutorial for making basic hilts!
    start here if new-start right here if your brand new fresh out of the factory never before opened noob!


  2. #2
    Council Member
    Jedi Council Member
    Jedi-Loreen's Avatar
    Join Date
    Dec 2005
    Location
    Not of this Earth
    Posts
    6,077

    Default

    No, the emitter, or blade holder, doesn't slide into the sink tube and get held with screws.

    If you're making a sink tube saber, you need 1 of these:
    http://www.thecustomsabershop.com/MHS-to-15-sink-tube-adapter--P162.aspx



    It's a sink tube adapter, you'll need one for your blade holder to screw into. This is what attaches to the inside of your sink tube with the button head screws. And you're going to need 4 of those screws, not just 2. They screw in from the outside, not the inside.

    And see the lip just below the threads? That's where your heat sink will sit, it will be sandwiched between this part and the blade holder when you screw it down.

    How did you think the LED and heat sink would be held in? Or did you think about that?



    In order to see the Light,
    you must sometimes risk the Dark.
    TCSS MODERATOR


    BLUE 8 Ready to ROCK and ROLL!

  3. #3
    Jedi Padawan astromech_kuhns's Avatar
    Join Date
    Aug 2008
    Location
    Korriban (sith temple)
    Posts
    637

    Default

    well i was thinking that the heatsink would do basically what was done in this: http://forums.thecustomsabershop.com...hread.php?t=20 and thats why i thought the sinktube woud slip over it.
    Last edited by Lord Maul; 12-14-2008 at 01:11 AM.
    if you are new these links will get you started

    tutorial on ohms law!!!
    the saber building dictionary-a dictionary with basically everything about sabers!
    thread index-this is the thread index!
    the basic saber building tutorial-tutorial for making basic hilts!
    start here if new-start right here if your brand new fresh out of the factory never before opened noob!


  4. #4
    Council Member
    Jedi Council Member
    Jedi-Loreen's Avatar
    Join Date
    Dec 2005
    Location
    Not of this Earth
    Posts
    6,077

    Default

    No, the Store doesn't carry those blade holders anymore. That tutorial is over 3 years old, the MHS parts were just being developed back then. The sink tube adapters are what are used now. With the regular blade holders.


    It does show that you read the tutorial though, so good show there. I can also see why you were confused.

    There's something that looks kind of similar in the store, but it's for 3/4 EL blades and is only meant to hold the mono jack for it.
    In order to see the Light,
    you must sometimes risk the Dark.
    TCSS MODERATOR


    BLUE 8 Ready to ROCK and ROLL!

  5. #5
    Council Member
    Jedi Master
    Obi-Dar Ke-Gnomie's Avatar
    Join Date
    Jul 2007
    Location
    Ontario, Canada
    Posts
    1,578

    Default

    Edited because J-Lo beat me to it and said almost the exact same thing.


  6. #6
    Council Member
    Jedi Council Member
    Jedi-Loreen's Avatar
    Join Date
    Dec 2005
    Location
    Not of this Earth
    Posts
    6,077

    Default

    Great minds..........
    In order to see the Light,
    you must sometimes risk the Dark.
    TCSS MODERATOR


    BLUE 8 Ready to ROCK and ROLL!

  7. #7
    Jedi Padawan astromech_kuhns's Avatar
    Join Date
    Aug 2008
    Location
    Korriban (sith temple)
    Posts
    637

    Default

    ya i saw that EL part to. i didnt realize when i clicked on the link that i was in EL specific and i got realy excited. it made me mad to find out it was EL o well though. its all good now. ive had my eye on that tutorial for ever. but i did notice they didnt sell those kits anymore.
    if you are new these links will get you started

    tutorial on ohms law!!!
    the saber building dictionary-a dictionary with basically everything about sabers!
    thread index-this is the thread index!
    the basic saber building tutorial-tutorial for making basic hilts!
    start here if new-start right here if your brand new fresh out of the factory never before opened noob!


  8. #8
    Council Member
    Jedi Master
    Obi-Dar Ke-Gnomie's Avatar
    Join Date
    Jul 2007
    Location
    Ontario, Canada
    Posts
    1,578

    Default

    Quote Originally Posted by Jedi-Loreen View Post
    Great minds..........
    I knew you were going to say that.


  9. #9
    Jedi Padawan astromech_kuhns's Avatar
    Join Date
    Aug 2008
    Location
    Korriban (sith temple)
    Posts
    637

    Default

    J-LO those pics you had were thos of the emmiter in the connection or the emmiter in the connection while connected to the sinktube?
    if you are new these links will get you started

    tutorial on ohms law!!!
    the saber building dictionary-a dictionary with basically everything about sabers!
    thread index-this is the thread index!
    the basic saber building tutorial-tutorial for making basic hilts!
    start here if new-start right here if your brand new fresh out of the factory never before opened noob!


  10. #10
    Council Member
    Jedi Council Member
    Jedi-Loreen's Avatar
    Join Date
    Dec 2005
    Location
    Not of this Earth
    Posts
    6,077

    Default

    Those pics are right from the store. Click on the link to the sink tube adapter.

    First pic, sink tube adapter alone.
    Second pic, adapter inside sink tube (not held in with screws, just sitting there).
    Third pic, blade holder screwed onto adapter that's inside sink tube.
    In order to see the Light,
    you must sometimes risk the Dark.
    TCSS MODERATOR


    BLUE 8 Ready to ROCK and ROLL!

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •