Does this look like a normal 5 watt LED?
Lens Color : Water Clear
Emitted Color : blue
Intensity Typ. : 100~120Lm
Viewing Angle : 160°
Forward Voltage : 3.0v-3.2v
Forward Current : 650mA
http://cgi.ebay.ca/2-Star-Bright-5W-...QQcmdZViewItem
Does this look like a normal 5 watt LED?
Lens Color : Water Clear
Emitted Color : blue
Intensity Typ. : 100~120Lm
Viewing Angle : 160°
Forward Voltage : 3.0v-3.2v
Forward Current : 650mA
http://cgi.ebay.ca/2-Star-Bright-5W-...QQcmdZViewItem
Blue 4 "Im hit!"
yeah they are nice led's those prolights, u can get them cheaper here
http://www.led-bulbs.com/eShop/10Bro...egory=Prolight
get the reflector to it makes it bright than the normal optics
Last edited by LeMoel; 08-28-2008 at 10:36 AM.
This is exactly why I keep trying to get people to STOP calling the Luxeon V LED's "5 watt LED's"
Watts is what you get when you multiply voltage and current. A green K2 is usually ran at 5 watts (3.9v x 1.5A = 5.85 watts). So... yes an LED that runs at different voltages can be a "5 watt LED." It depends on the current.
Luxeon I series is "Luxeon one" not "Luxeon 1-watt"
Luxeon III series is "Luxeon Three" not "Luxeon 3-watt"
Luxeon V series is "Luxeon Five" not "Luxeon 5-watt"
Cheers,
To bad hes not talking about a lux led.
Any intelligent fool can make things bigger and more complex. - Albert Einstein
Reaganomics not Obamanomics
So what are we to call them then? Nonlux Lux III/V?
Any intelligent fool can make things bigger and more complex. - Albert Einstein
Reaganomics not Obamanomics
X-Wing and I have been trying to do the same for a few years, but not to much avail.
I say... if the people don't want to listen, fine.
But for those reading--I don't care WHAT you hear, what Eandori is saying here is the de facto way to look at wattage when regarding LEDs.
"2w LED" or whatever... is not about "non-Lux"... it's just bloody non-sequitur.
~~ GREYTALE NOVASTAR (Writer, Director, Choreographer, Sound Designer, Actor, Saber Designer, Vocal Artist)
~~ Balance of Power, EP I: "Into The Lion's Den"
~~ Balance of Power, EP II: "Ashes of The Phoenix"
~~ The Crystal Focus Sound CD Compendiums... are HERE! ~~
~~ Nova & Caine's Staged Combat System... comin' SOON!
~~ Crystal Focus Wiring Guide
This is the reason my comments do apply Hasid.
Note that his first question was what he believed was a contradiction. He knew Luxeon V LED's run at voltages around 6.85v forward, and he knew they were often called "Luxeon 5 watts"5 watt LED that runs at 3.2v?
Does this look like a normal 5 watt LED?
Lens Color : Water Clear
Emitted Color : blue
Intensity Typ. : 100~120Lm
Viewing Angle : 160°
Forward Voltage : 3.0v-3.2v
Forward Current : 650mA
So it didn't make sense to the original thread author that you can have a "5 watt LED" that runs at 3.2v instead of 6.85v. If people on these boards did not incorrectly refer to Luxeon V's as "5 watt LED's" then this author would not have gotten confused.
Or... if he knew the basic equation to calculate power he also would not have gotten confused, but I guess not many people know that voltage times current = power.
Cheers,
it's funny, I have a guy posting on one of my youtube vids talking about... (**drumroll**) a "10w" LED. He seems to know quite a bit, but insists that...
... "10w" is accurate at a range of voltages for the LED's fwd v from 8.1v to 12.8v (or something). WHAT?!?!?!
For those reading... again... this makes NO SENSE. *HOW* could the wattage remain "the same" if you're varying one of the values all over the place???!?!?! WTF??!?!?!? And please everyone--don't forget that voltage is RELATIONAL to current. If you change one--you usually affect the other to some extent.
But anyhow, even if you don't have electronics experience... IT STILL MAKES NO SENSE. It's akin to the following:
2 * 2 = 4
but...
2 * 5 = 4 also... (!!)
and...
3 * 2 = 4
and
4 * 4 = 4 ... .... (WHAT!!)
just like:
2v @ 2A = 4 watts
but...
2v @ 5A = 4 watts also
and...
3v @ 2A = 4 watts
and
4v @ 4A = 4 watts ... .... (WHHEEEEEEE!!!!!...)
GIGO.
~~ GREYTALE NOVASTAR (Writer, Director, Choreographer, Sound Designer, Actor, Saber Designer, Vocal Artist)
~~ Balance of Power, EP I: "Into The Lion's Den"
~~ Balance of Power, EP II: "Ashes of The Phoenix"
~~ The Crystal Focus Sound CD Compendiums... are HERE! ~~
~~ Nova & Caine's Staged Combat System... comin' SOON!
~~ Crystal Focus Wiring Guide
General rule is (as some of you prob already know):
P (effect/Watt) = U (Voltage/Volt) x I (Current/Amp)
Unless someone overturn the laws of electronics,
I think it will stay that way for a long time.
I gather that the most important thing is how YOU think the saber looks in RL.
If you must, you can also sometimes compare similar colors in lumens.
But the only thing that I see Watt is influencing, is the power drain.
CybKnight -
For honor in gaming and beyond
Bookmarks