Results 1 to 9 of 9

Thread: Batterys @ 3000mAh

  1. #1

    Default Batterys @ 3000mAh

    Hi i have aquired these for my battery pack

    Battery.jpg

    18650 3000mAh 3.7volt li-ion batterys

    now chargers over here are harder to find than the USA :-/

    everything seems to be 7.2 v here below:
    http://www.ebay.co.uk/itm/New-High-P...3443%26ps%3D54

    i have a 7.4v controller:

    http://www.ebay.co.uk/itm/4003935155...84.m1497.l2649

    can i use the above charger with the battery? will this charge to 7.4 volts? or will 3000mAh be too much for the PC2 board and the LEDS?
    Last edited by MKnight; 02-05-2013 at 09:39 AM.

  2. #2

    Default

    No, That charger is for a different type of battery. You need one like this:

    http://www.thecustomsabershop.com/37...rger-P129.aspx

    Hokey religions and ancient weapons are no match for a good blaster at your side, kid.

  3. #3

    Default

    Be sure you get a Li-Ion charger. If the charger is only for NiMH or NiCd, then it won't work. Some smart chargers support multiple types, but it MUST support Li-Ion or you risk blowing the batteries up. Explosively.

    mAh is a measure of capacity. The higher it is, the more power the battery can store. Think of it like a fuel tank. Bigger fuel tanks run longer without needing to refuel. You can use as high of a mAh battery pack in a saber as you like.
    We all have to start somewhere. The journey is all the more impressive by our humble beginnings.

    http://led.linear1.org/1led.wiz for the lazy man's resistor calculator!
    http://forums.thecustomsabershop.com...e-to-Ohm-s-Law for getting resistor values the right way!

  4. #4

    Default

    The 3000mAh has to do with how long the battery will last. With this one you could run 1000 milliamps for 3 hours, or 1500 milliamps for 2 hours. So, it wont be too much for the PC2.

    However, concerning the charging, I'm no expert, but the charger I have has a switch so you can set it to 3.6V, 7.2V, 10.8V and 14.4V.
    So, my guess would be that you need to charge it at slightly less then the batteries voltage, just judging from how this charger works.
    So, if you're making a 7.4v pack, you should be able to use the charger you have linked, NOOO, this is wrong, i didnt realize it was a Ni-MH/Ni-Cd charge you had. DO NOT USE THAT, as mentioned by others above but if you are using the single 3.7v cell, it sounds like that could be dangerous using that charge.

    Could you order one of these? Or can they not be shipped to your location?


    Saber on.
    Last edited by The Yin; 02-05-2013 at 11:22 AM. Reason: dont listen to me!!
    ~ The Yin ~

    “Yeah I’m pack’n heat! It’s to prevent anyone from making me cold.”

    For the saber building Younglings and Padawans: Basic Saber Building and The Saber Building Dictionary!

  5. #5

    Default

    Ok my prob is postage for the charger on the store is $50 to the UK. I was under the impression i could pick up a charger in the UK for li-ion batterys..

    No chance... What a f'ing nightmare...

  6. #6

    Default

    A quick search on Amazon UK found some li-ion chargers for out-of-hilt recharging.
    We all have to start somewhere. The journey is all the more impressive by our humble beginnings.

    http://led.linear1.org/1led.wiz for the lazy man's resistor calculator!
    http://forums.thecustomsabershop.com...e-to-Ohm-s-Law for getting resistor values the right way!

  7. #7

    Default

    Got the linky? i cant find any...! i need in hilt charging though...!


    actually i found this bad boy :
    http://www.amazon.co.uk/gp/product/B...ls_o00_s00_i00
    Last edited by MKnight; 02-06-2013 at 06:33 AM.

  8. #8

    Default

    That should do the job just fine.
    We all have to start somewhere. The journey is all the more impressive by our humble beginnings.

    http://led.linear1.org/1led.wiz for the lazy man's resistor calculator!
    http://forums.thecustomsabershop.com...e-to-Ohm-s-Law for getting resistor values the right way!

  9. #9

    Default

    Yes could not find anything all week, this has been ordered and should be here this week...

    now i just need my saber order and im good to go

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •