Aurum Solis
The Aurum Solis, or Golden Sun saber project parts list.
Blade Holder style 19
8-32 x 3/8" button head screw(blade retention)
Hilt style 1 with guarded style switch hole
MPS Pommel style 6
MPS Clip
MPS Insert style 4
SPST Latching Guarded switch with silver button
4AAA battery holder
3.3ohm 5w resistor
Luxeon Rebel Led Star Amber
Luxeon Collimator Lens 5 deg viewing angle
Luxeon III/V Lens Holder
UltraEdge Blade
Heres a crude concept drawing.
Anything I forgot or should change lemme know
Last edited by Mal Rune; 12-18-2009 at 01:44 PM.
Aurum Solis on the FXsabers forum
"There is no such thing as luck..."
Maybe a Covertec button or a D ring for hanging your saber from a belt. Other than that it looks good to me. A more senior member here might have a little more insight.
So this is how liberty dies... with thunderous applause.
You will have to sand down the utra edge blade to get it to fit in the bladeholder...
But other than that I think you're good to go.
Got a Question? There's a thread for that...
~Do what you can, with what you have, where you are.~Teddy Roosevelt
SollusVir everywhere else... FXsabers, Youtube, etc...
Really? Is the ultra edge bigger than 1 inch? I think theres a smaller ultra edge made for graflex replica's, but I figured it was 3/4"...
Last edited by Mal Rune; 12-18-2009 at 01:40 PM.
Aurum Solis on the FXsabers forum
"There is no such thing as luck..."
No, there isn't a smaller UltraEdge that is 3/4"....and the Ultrasaber's polycarbonate supplier makes theirs slightly larger than Tim's so they are not a direct fit in the MHS blade holders. Tim makes those to fit the polycarbonate he sells, which stands to reason, since the MHS is his thing, not Ultrasabers'.Originally Posted by Mal Rune
Got a question? Start Here. Have you tried the Thread Index yet? Most questions can be answered there.
Well I dont think it will be to much trouble. Im sure I can sand it down a bit...and yeah I just took a look at the UltraEdge that I figured was 3/4. It seems I misunderstood the description. Anyways is the 3.3ohm 5watt resistor the right choice for a Rebel? I used a resistor calculator, and read that rebels use about the same amount of power as a seoul P4, but I'd like to here a professionals opinion just to be sure.
Last edited by Mal Rune; 12-18-2009 at 04:03 PM.
Aurum Solis on the FXsabers forum
"There is no such thing as luck..."
It would be easier to just buy the thinwalled blade and make your own cellophane diffuser.
That's what an ultraedge blade is...
Got a Question? There's a thread for that...
~Do what you can, with what you have, where you are.~Teddy Roosevelt
SollusVir everywhere else... FXsabers, Youtube, etc...
The UltraEdge is made of white polycarbonate. Not clear. Therefore they arent the same, and the blade holder on Ultrasabers oppressor is blade holder 19, and seems to fit the Ultra Edge just fine..granted they could'ev machined it, but some minor sanding shouldnt be a problem. Besides if all else fails I'll just get one of tims blades. Thanks for your input
Aurum Solis on the FXsabers forum
"There is no such thing as luck..."
huh?
what makes you think/say that?
Just from what I've seen in vids...
I can't tell the difference from the two.
Got a Question? There's a thread for that...
~Do what you can, with what you have, where you are.~Teddy Roosevelt
SollusVir everywhere else... FXsabers, Youtube, etc...
Posting Permissions
Reply With Quote
Bookmarks