Creating simple saber for costume

[jedi Xam'i Letsab]

if I have the following parts do I have enough for a working saber with sound and effects on it.
7" Fluted with standard style switch hole
Qty: Update Delete
Price: $25.00
Build Your Own
Luxeon III / Seoul P4 Electronics Kit
4AAA battery holder
Red/Orange
Collimator Lens 5° viewing angle
2.2ohm 5w resistor
Push on/push off switch with red button
Luxeon III/V Lens Holder
Qty: Update Delete
Price: $18.36
Screw on LED blade holder style 10
Qty: Update Delete
Price: $23.95
1" Thick walled Polycarbonate 40" long (No)
Qty: Update Delete
Price: $12.99
Bullet shaped tip for 1" thick walled blades
Qty: Update Delete
Price: $6.00
Blade film (Double wrap +$3.00, 1" Thick walled)
Qty: Update Delete
Price: $7.50
MPS Pommel style 4
Qty: Update Delete
Price: $5.99
Luxeon 3w driver V2 (Momentary)
Qty: Update Delete
Price: $50.00
MPS Insert style 2
Qty: Update Delete

[Jedi-Loreen]

In the future, please don't post your list of items in your cart like that. All that extra stuff we don't need to see makes it hard to read the list.

Post it like this:

7" Fluted with standard style switch hole

Build Your Own
Luxeon III / Seoul P4 Electronics Kit
4AAA battery holder
Red/Orange
Collimator Lens 5° viewing angle
2.2ohm 5w resistor
Push on/push off switch with red button
Luxeon III/V Lens Holder

Screw on LED blade holder style 10

1" Thick walled Polycarbonate 40" long

Bullet shaped tip for 1" thick walled blades

Blade film

MPS Pommel style 4

Luxeon 3w driver V2 (Momentary)

MPS Insert style 2


You have nothing on your list that gives you sound, you'll have to add that yourself.

If you're ordering the Momentary Luxeon 3w driver (which is not a sound board), then you need to make sure to choose a momentary switch with your Build Your Own Luxeon III / P4 electronics kit.

You also need an MPS clip to hold the MPS Insert in your Pommel.

[jedi Xam'i Letsab]

so what does the driver do? I read it and it says that it has clash and swoosh is that the lighting effects only? or have I confused the wrong board?

[Jedi-Loreen]

* Ramp up/down, static shimmer, optional flash on impact and lockup
* Maximum input voltage has been increased to 30V from the previous 12V
* Maximum output voltage has been increased to 25V. Rebel compatible.
* Uses less than 0.2mA when sleeping (turned off, with power to driver)
* Size is reduced by 35%, 0.80 x 1.1 from previous 1.25 x 1.625
* Pulsed Width Modulation averages 1A output with 1.2A when “clashing”
* On board micro on/off switch with contacts for remote switch
* Available in momentary or latching switch configurations

"Clashing" is just a lighting effect, same as "flash on impact".

I don't see anything in the description about "swoosh".

[jedi Xam'i Letsab]

OH ok. thanks for clarifying that. so from what I got from the shout chat was that I could use the hasbro board for the sound, but I got disconnected when I asked if that could be used as a driver

[jedi Xam'i Letsab]

this is the design that I made with all those parts

[Rhyen Skytracker]

In this thread it tells you which LEDs work best with the economy hasbro card. I will also tell you which hasbro sabers are the best to get.

http://forums.thecustomsabershop.com...ead.php?t=7587

[jedi Xam'i Letsab]

oh ok. with the double male slotted extender you can't add a blade holder to the end can you?

[DJMoonbass]

just for future reference. double posts are a no no. you did a double post right above skytrackers post. also your MHS saber should be cool. i think it needs a choke section though.. in my opinion... i wouldnt get the driver if you dont plan on using sound. allthough you could wire up a MR or Cheapy hasbro board. youd need to do some research on how to use the 3w driver with these boards as well as power requirements and stuff. its no easy task