Got a question? Start Here. Have you tried the Thread Index yet? Most questions can be answered there.
Copper transfers the heat way better than aluminum so in 30 seconds the copper heat sink should actually be hotter or the same temp as a aluminum one so that shouldn't be the issue.
Tim
The Custom Saber Shop
I think something is wrong with the pucks,, I just dont see how an led could get super hot without poofing.
Any intelligent fool can make things bigger and more complex. - Albert Einstein
Reaganomics not Obamanomics
To echo this so people don't miss it... Tim is exactly right.
If a heatsink *IS* actually doing its job... umm... it should get hot. Sure, not inordinately so, but... heat is heat is heat is heat. The amount of heat generated from your battery + LED setup does not change when you're using a heatsink made of aluminum or copper... nor wood or leather!!! Granted, wood and leather would... uh... not do so well in helping to keep the heat under control.
That all being said... Hmmmmmmm... you know... there *IS* a sort of "too much is too much" point regarding all this. In other words... if the heat produced somehow is JUST too much for the heatsink (and other metal parts like the hilt)... it becomes sort of a cascading effect. Sort of like if an LED is allowed to "suck in" too much current... you get this sort of geometric-like cascade of death, lol.
But still... I don't know why a P4 @ 1A would do such a thing. I mean... I *THINK* that's supposed to be spec????
Hmm... well... I will say this:
* Running a P4 GREEN
* @ 1200mA
* Using CF
* Using Tim's "smaller" aluminum heatsink, the one from the 1.25" blade holder thingy
* No heat issues that I'm aware of...
So... the Puck DOES seem pretty suspect. Maybe I should try a direct drive P4 white setup and run the bloody 'ell out of it and see if I can make some fireballs, heheheh
~~ GREYTALE NOVASTAR (Writer, Director, Choreographer, Sound Designer, Actor, Saber Designer, Vocal Artist)
~~ Balance of Power, EP I: "Into The Lion's Den"
~~ Balance of Power, EP II: "Ashes of The Phoenix"
~~ The Crystal Focus Sound CD Compendiums... are HERE! ~~
~~ Nova & Caine's Staged Combat System... comin' SOON!
~~ Crystal Focus Wiring Guide
Hi Guys,
I may not be right about this but it sounds to me like maybe there is some kind of contact with the LED wire up and the heatsink causing some type of short but still being able to light up the LED. DC voltage has a tendency to heat up metal quickly when shorted out. I could be wrong but it might be possible.
I'M JUST A SPY(LOL)
But 3 pucks in a row? It just not very likely. Plus, I think he measured one and it puts out 1000mA.
I wonder does the LED look as bright as it should be? The short idea sounds like it might have some merit. He did say the emitter melted itself right out of it's solder. That's pretty amazingly hot.
Last edited by Jedi-Diah; 10-01-2008 at 12:30 AM.
Ok but look how many pucks there are in the world. I have no shadow of a doute that there are more pucks out there that are bad.
It could be that a handfull could be bad or it could be millions that are bad.
Any intelligent fool can make things bigger and more complex. - Albert Einstein
Reaganomics not Obamanomics
well whatever the answer is i thiunk iam just going to try the copper heatsink, then this shouldnt be a problem
I think it will still be a problem. The copper heat sink may dissipate heat better but the LED overheating is still bad. It will, at the very least, shorten the lifespan of the LED. It would be odd if the LED itself was the reason for the overheating but since the buck puck delivers a continuous current, it is really hard to say that the buck puck is at fault.
I do. I have a lux 3 green and a lux 3 red. Both are using copper heatsinks. No trouble whatsoever.
I did however try this for the first time. I put the P4 on the copper heatsink, then put it inside my MHS saber hilt. Took a longer amount of time, but the hilt got so hot that I was not able to touch the handle it was so hot after about 90 seconds. When I took the Hilt back apart, the little legs that hold the lense holder on the LED star, melted off. It took me 30 minutes just to clean all the melted plastic and super glue off the LED and heatsink. At this point, I'm really beginning to think, the $8 LED is not worth the trouble of burning my fingers and ruining parts to try to get it to work.
Bookmarks