Page 1 of 2 1 2 LastLast
Results 1 to 10 of 14

Thread: How do you assemble the "kit"

  1. #1

    Default How do you assemble the "kit"

    I got the starter kit all ready to go, I now understand that I have to make the hole for the blade screw - probably good to learn that skill anyway...

    But some directions of how it all goes together would have been really cool.

    I am certain that it likely is somewhere on the forums, but i have not been successful in locating the directions as of yet.

    Any thanks here would be appreciated.

    The kit I have is the MHS Starter Kit

    Ray

  2. #2

    Default

    Everything about wiring you need to know is right here:

    http://www.thecustomsabershop.com/sa...sp?TOPIC_ID=22

    Just ignore alot of the stuff bout the sink tube, and go straight to the wiring.

  3. #3
    Owner of the Custom Saber shop Strydur's Avatar
    Join Date
    Oct 2005
    Location
    USA
    Posts
    3,454

    Default

    Or better yet..the LED MHS tutorial

    http://www.thecustomsabershop.com/sa...sp?FORUM_ID=20

    Tim
    The Custom Saber Shop

  4. #4
    Council Member
    Jedi Council Member
    xwingband's Avatar
    Join Date
    Nov 2005
    Location
    The training simulators, duh!
    Posts
    5,898

    Default

    Yes, and learn the edit feature. 4 posts within 20 minutes of eachother without a responce... that's what the feature is for.

    <center>
    www.dewbackwing.com</center>

  5. #5

    Default

    <blockquote id="quote"><font size="1" face="Verdana, Arial, Helvetica" id="quote">quote:<hr height="1" noshade id="quote">Originally posted by StrydurOr better yet..the LED MHS tutorial<hr height="1" noshade id="quote"></blockquote id="quote"></font id="quote">Woah! I didn't even notice that... Sweet!!

  6. #6

    Default

    <blockquote id="quote"><font size="1" face="Verdana, Arial, Helvetica" id="quote">quote:<hr height="1" noshade id="quote">Originally posted by RayHayden

    Oh - by the way, I STILL need to figure out how to wire it up correctly...

    Specifically, Little battery pack red wire goes to? Black goes to? Resistor gets soldered in where? And the two wires coming off the switch get connected to what?

    I know I could probably figure it out (but for the resistor), but someone who knows would be faster and again - appreciated... also..

    Any suggestions for padding material for the battery holder? And agin, thanks in advance!

    Ray
    <hr height="1" noshade id="quote"></blockquote id="quote"></font id="quote">What the... You already said that!!

  7. #7

    Default

    Those directions are the ones I was looking for! WooHoo... thank you very much - I KNEW I saw them here before!

    Ray

  8. #8

    Default

    Use the EDIT! Quintuple posts just piss everyone off.

    EDIT: See? It works. The button has a picture of a pencil and paper.
    Good thing there's no Rep system on these boards. You'd be neg repped into oblivion.

    Those who see the light at the end of the tunnel, need to stop staring at the sun.

  9. #9

    Default

    <blockquote id="quote"><font size="1" face="Verdana, Arial, Helvetica" id="quote">quote:<hr height="1" noshade id="quote"> Or better yet..the LED MHS tutorial

    http://www.thecustomsabershop.com/sa...sp?FORUM_ID=20

    <hr height="1" noshade id="quote"></blockquote id="quote"></font id="quote"> Cool Design Tim, I have been wondering how the Quick Change Led feature actully works, (Light Bulb goes on) finally I see!![]

    May the Force
    Be with You

    Marc E.

  10. #10

    Default

    Newest Update on my progress with the MHS Kit...

    It is done... for now! I was concerned about the drilling and tapping the hole, but it was very easy to do.

    I used my Dremel. I used a very fine drill bit to start a very tiny hole, then used the next size up to make a wider hole - I don't have a vice, so I had to hand hold it and move very slowly.

    I then used the largest Dremel bit and made the hole through. It is just short of being the perfect size for a 8 by 32 hole.

    Then I used the Tapping tool to make the threaded hole - that took a while, but it worked out very well... having to back out and remove little metal bits quite often.

    It is hard to find the perfect thumb screw at Home Depot, perhaps ACE has one...

    Anyway, I got the white LED and it looks great. The little colored disks are awesome for changing the color at my whim too! Actually a disk that looks orange a little is the perfect yellow for what I wanted.

    If I figure out how to post a picture of it, I will. Not to worry, it will be an awesome picture, shooting video and doing photography is what I do for a living!

    Best wishes,

    Ray


Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •