View Poll Results: This troubleshooting FAQ/Guide helped solve my CF issue...

Voters
16. You may not vote on this poll
  • Yes! Thanks Erv, thanks Novastar!

    12 75.00%
  • No. Dude... you just bring on the *suck*, N-Star...

    4 25.00%
Page 11 of 12 FirstFirst ... 9 10 11 12 LastLast
Results 101 to 110 of 114

Thread: Crystal Focus TROUBLESHOOTING thread...

  1. #101

    Default

    I helped my son install a cfx and everything works but we are getting an overheating warning while everything is in the hilt. Any suggestions on what I can do to, thanks for any help. He has a tri-cree LED and I believe that the resistor is the issue for the red LED but I don't know.
    Last edited by gggLITCH; 05-27-2020 at 02:54 PM.

  2. #102

    Default

    Quote Originally Posted by gggLITCH View Post
    I helped my son install a cfx and everything works but we are getting an overheating warning while everything is in the hilt. Any suggestions on what I can do to, thanks for any help. He has a tri-cree LED and I believe that the resistor is the issue for the red LED but I don't know.
    adjust your htemp settings to a higher temperature
    Props Electronics
    http://www.plecterlabs.com

  3. #103

    Default

    I'm looking to make LED pucks to wire to a PCB neopixel disk for CFX to adapt a neopixel saber into a more combat capable saber for sparring purposes. What kind of power output do I have to accommodate for when choosing my resistor?

  4. #104

    Default

    I can't find out how to change fonts in single switch mode on the CFX.

    I must be missing something glaringly obvious, but I can't seem to find anything about it in the Crystal Focus 10 manual!

    EDIT: After hours of troubleshooting, I finally discovered the secret.

    If anyone else has the same question and comes across my post, hopefully this can help. In order to enter the soundbank selection and change fonts without an auxiliary switch, you must be holding down the activation switch while the saber is booting.

    The easiest way to do this is by holding the activation switch while removing the kill key; however, you can also restart the saber by holding down the activation switch for about 10 seconds (while the saber is already deactivated). Basically, just hold down the button until you hear the words: "soundbank selection". From there, a tap on the button will cycle the fonts forward, while holding the activation switch will select that font.
    Last edited by SonOfRevvan; 06-10-2020 at 02:05 PM.

  5. #105

    Default

    Have a CFX I've installed in a Korbanth AS2, with an RGB Tri-Cree. Everything seems wired together correctly. When powered up, everything works fine, except LED not lighting up. I had a similar problem when I installed a Quigon saber recently, and changing strippower=0000 worked, but it's not with this install. LEDs are good - tested prior to install. Any help is greatly appreciated. Config:

    //CF-X Configuration
    debug=0
    logport=0
    vol=100
    menuvol=100
    menugest=0
    beep=40
    muteb=0
    muteoff=0
    sleep=50000
    deep=0
    qkignite=0
    orient=0
    valsnd=0
    switch=2
    offp=0
    offd=200
    onp=0
    ond=20
    swing_flow=360
    clash_flow=300
    spin_flow=400
    smooth_flow=1000
    lockup=300
    loop=1
    shuffle=2
    plilh=3400,4200
    omnisense=2000
    bladepower=100
    ledstrip=0
    auxstrip=0
    tridentstrip=0
    accentstrip=0
    dragstrip=20
    strippower=0000
    ls1_timings=350,700,24,1,3
    ls2_timings=350,700,24,1,3

    ## Motion Settings
    gate=50
    smooth_gate=50
    hclash=850
    hswing=450
    hslash=400
    hhybrid=550
    hforce=300
    hfclash=650
    hstab=500,-20,20
    hspin=750
    htwist=350
    hdrag=500,-90,0
    htemp=40
    spectrum_mode=0
    spectrum_axis=0
    field=10,10,10

    [profile=0]
    wakeup=1
    randc=0
    blastp=0
    random=2
    pom=0
    pof=0
    poi=0
    magic=0
    saberlock=0
    blastm=0
    randb=2
    shmrd=150
    shmrp=12
    shmrr=24
    shmr%=60,99
    focd=200
    focp=20
    focr=28
    foc%=60,99
    focl=1
    focb=1
    focf1=1
    focf2=1
    focf3=0
    fade=0
    flks=6
    flkd=25
    tridentflk=0
    flkon=1
    flkoff=1
    pulsed=0
    pulsel=0
    on_fade=1
    off_fade=1
    unstable=0
    style_pon=0
    style_poff=0
    style_blaster=2
    style_lockup=1
    style_drag=2
    style_flicker=1
    style_clash=1
    style_stab=0
    over_pon=0
    over_poff=0
    pos_lockup=60
    size_lockup=40
    mapping_color=0
    mapping_unstable=1
    mapping_lockup=1
    mapping_drag=1
    mapping_flicker=1
    hcool=70
    lcool=0
    sparkf=120
    sparkd=10
    drift=1
    mapb=100
    mapc=70
    refreshfx=12
    omnisabers=0
    sbolt=8,20
    dbolt=40,810
    lbolt=15,30
    fbolt=1
    rbolt=10
    qbolt=50

    ## [profile=1]

    ## [profile=2]

    ## [profile=3]

    ## [profile=4]

    ## [profile=5]
    Last edited by Huge.eug; 07-28-2020 at 06:01 PM.

  6. #106

    Default

    Please post the Color profiles you have also.
    TCSS MODERATOR
    All n00bs READ these first (PLEASE)!!!:
    1. Forum Guidelines
    2. FJK’s “Down and Dirty” guide to Ohm’s Law

    "Yeah, yeah, I've heard it all before... you want blindingly bright, super loud, running 1138 blinkies off of the cheapest sound card you can find AND you want all of it to run on a battery the size of a dime, and run for a very, VERY long time. That one cracks me up every time..."
    My email: fjk_tcss@yahoo.com

  7. #107

    Default

    Sorry, it was a long day at work. I had basically wanted first color to be blue, 2nd red. Maybe I messed this up. Thanks, FJK!

    [color]
    color=0,0,1023,0
    fcolor=1023,1023,1023,0
    lcolor=1023,1023,1023,0
    bcolor=1023,1023,1023,0
    xcolor=1023,0,0,0
    mcolor=1000
    tridentm=0000

    [color=1]
    color=1023,0,0,0
    fcolor=1023,1023,1023,0
    lcolor=1023,1023,1023,0
    bcolor=1023,1023,1023,0
    xcolor=1023,255,0,0
    mcolor=1100
    tridentm=0000

    [color=2]
    color=1023,660,0,0
    fcolor=1023,1023,1023,0
    lcolor=1023,1023,1023,0
    bcolor=1023,1023,1023,0
    xcolor=1023,660,0,0
    mcolor=1100
    tridentm=0000

    [color=3]
    color=340,1023,0,0
    fcolor=1023,1023,1023,0
    lcolor=1023,1023,1023,0
    bcolor=1023,1023,1023,0
    xcolor=40,1023,0,0
    mcolor=1100
    tridentm=0000

    [color=4]
    color=145,1023,0,0
    fcolor=1023,1023,1023,0
    lcolor=1023,1023,1023,0
    bcolor=1023,1023,1023,0
    xcolor=145,1023,0,0
    mcolor=1100
    tridentm=0000

    [color=5]
    color=0,1023,0,0
    fcolor=1023,1023,1023,0
    lcolor=1023,1023,1023,0
    bcolor=1023,1023,1023,0
    xcolor=0,1023,0,0
    mcolor=0100
    tridentm=0000

    [color=6]
    color=0,1023,340,0
    fcolor=1023,1023,1023,0
    lcolor=1023,1023,1023,0
    bcolor=1023,1023,1023,0
    xcolor=0,1023,340,0
    mcolor=0110
    tridentm=0000

    [color=7]
    color=0,1023,635,0
    fcolor=1023,1023,1023,0
    lcolor=1023,1023,1023,0
    bcolor=1023,1023,1023,0
    xcolor=0,1023,635,0
    mcolor=0110
    tridentm=0000

    [color=8]
    color=0,1023,1023,0
    fcolor=1023,1023,1023,0
    lcolor=1023,1023,1023,0
    bcolor=1023,1023,1023,0
    xcolor=0,1023,1023,0
    mcolor=0110
    tridentm=0000

    [color=9]
    color=0,0,1023,0
    fcolor=1023,1023,1023,0
    lcolor=1023,1023,1023,0
    bcolor=1023,1023,1023,0
    xcolor=0,0,1023,0
    mcolor=0010
    tridentm=0000

    [color=10]
    color=115,0,1023,0
    fcolor=1023,1023,1023,0
    lcolor=1023,1023,1023,0
    bcolor=1023,1023,1023,0
    xcolor=115,0,1023,0
    mcolor=1010
    tridentm=0000

    [color=11]
    color=355,0,1023,0
    fcolor=1023,1023,1023,0
    lcolor=1023,1023,1023,0
    bcolor=1023,1023,1023,0
    xcolor=355,0,1023,0
    mcolor=1010
    tridentm=0000

    [color=12]
    color=1023,0,1023,0
    fcolor=1023,1023,1023,0
    lcolor=1023,1023,1023,0
    bcolor=1023,1023,1023,0
    xcolor=1023,0,1023,0
    mcolor=1010
    tridentm=0000

    [color=13]
    color=1023,0,50,0
    fcolor=1023,1023,1023,0
    lcolor=1023,1023,1023,0
    bcolor=1023,1023,1023,0
    xcolor=1023,0,50,0
    mcolor=1010
    tridentm=0000

  8. #108

    Default

    Unless you have strips specially set up that way, the normal sequence is RGB. Color 1 would (should) be a straight red blade. You’re likely on Color 0 right now, but you’re not likely seeing anything because the header says [Color] and NOT [Color = 0]
    Last edited by Forgetful Jedi Knight; 07-31-2020 at 07:31 PM.
    TCSS MODERATOR
    All n00bs READ these first (PLEASE)!!!:
    1. Forum Guidelines
    2. FJK’s “Down and Dirty” guide to Ohm’s Law

    "Yeah, yeah, I've heard it all before... you want blindingly bright, super loud, running 1138 blinkies off of the cheapest sound card you can find AND you want all of it to run on a battery the size of a dime, and run for a very, VERY long time. That one cracks me up every time..."
    My email: fjk_tcss@yahoo.com

  9. #109

    Default

    Quote Originally Posted by Forgetful Jedi Knight View Post
    Unless you have strips specially set up that way, the normal sequence is RGB. Color 1 would (should) be a straight red blade. You’re likely on Color 0 right now, but you’re not likely seeing anything because the header says [Color] and NOT [Color = 0]
    I'm not sure why, but the Color = 0 did not copy and paste correctly. It's always been Color = 0. Sorry about that. I just double checked and tested it again, still no light.

  10. #110

    Default

    I’d then check your wiring. And do it outside the hilt.
    TCSS MODERATOR
    All n00bs READ these first (PLEASE)!!!:
    1. Forum Guidelines
    2. FJK’s “Down and Dirty” guide to Ohm’s Law

    "Yeah, yeah, I've heard it all before... you want blindingly bright, super loud, running 1138 blinkies off of the cheapest sound card you can find AND you want all of it to run on a battery the size of a dime, and run for a very, VERY long time. That one cracks me up every time..."
    My email: fjk_tcss@yahoo.com

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •