Tools of the Trade

[nich]

Ok I'm new to the site and how every thing works. I'm not going to be very creative on my first saber. I've read through the tutorials but what I'm missing is the tools that are needed. I get a basic Led Hilts set up. I know that I would need a soldering iron what kind of drill bits would I need and what would I use to cut the sink tub. Can anybody help me with this. Thank you for you time in reading my post.
Nich

[Darth Frieds]

to cut the sink tube, use a dremel or rotary tool

I have surrendured to the ways of the darkside. Fear is my ally

[vadeblade]

Well here is my list of tools to build a basic lightsaber:

***SAFETY GLASSES***

Dremel w/ the following accesories-
...cut-off disk
...reinforced cut-off disk
...sanding drum
...assorted high-speed cutters

screw tap w/ appropriate drill bits -
...#4-40 tap w/ No. 43 drill bit
...#6-32 tap w/ No. 36 drill bit
...#8-32 tap w/ No. 29 drill bit

hacksaw
set of allen wrenches
assorted wet/dry sand paper
lots of masking tape
tap or cutting oil
vise grips
vise (optional but handy)

ohh, and buy a good pair of safety glasses.


Lightsaber Warning Label: "CAUTION: Do NOT attempt to sharpen blade."

http://www.geocities.com/projectstm/lightsaber.html

[vadeblade]

Also want to add the the flex-shaft attachment for the Dremel makes the rotary tool much easier to use. Get one of those if you can afford one.

Lightsaber Warning Label: "CAUTION: Do NOT attempt to sharpen blade."

http://www.geocities.com/projectstm/lightsaber.html

[LAN-ED-TUL]

one other thing that might be added to list:

BANDAIDS lol

You dont know the POWER, of the dark side...

[nich]

OK So what is a screw tap?

[xwingband]

It's the tool you use to put threads on a hole you just drilled.

<center>
www.dewbackwing.com</center>

[nich]

Does any one have any preferences on what type of dremel that they like. I've been looking at the black and Decker Dremel and the DREMEL name brand. I was also wondering if anybody has done any paint work and with out the power cotting if there was something another type of paint that could be used. Thank you everybody for your replies so far.

[Mur-Pa DiLos]

As far as the rotary tool is concerned only go with the Dremel. They have a nice warranty and all the cool accessories work great! (especially that little pencil, flexi, thingy thing.) When in doubt always go for the better model. I prefer the twin speed over the single at least so you can adjust the speed. I have one that adjusts the speed so nicely that I can even use it to screw in screws! (which for those who have used one know that is impossible at 35,000 rpms!)

I'm currently building my first hilt, and the paints that Michael's sells for plastic stuff to make it look different seems to be working nicely for some neat different styles. Also, you can go with the tried and true Testors paint for models. Plastic is plastic if you sand it right. Mostly when it comes to painting, prepping is key, a good prep with a crappy paint job will always look better than a crappy prep, and a good paint spray. (note how I didn't say "job")

Go with the Dremel, and for the paint, make sure that it adheres to whatever you're trying to paint on, and prepping is key.[]

Other than that, just make sure that your finger stays away from the cut-off wheel or you can talk about the experience like the rest of us have.

As Cain would say, If there isn't any blood drawn by the end of the project, than you didn't work hard enough or it isn't done."[]

okay I know that was cheesey and not really yours Cain, but it was somewhere along those lines.[]

[scaarmor]

The sign of a job well done is BLOOD. I have never had a project, job, etc. go correctly if I did not bleed. Conversly, every time I have bled the project turns out perfect! I have even sometimes, after working on a car when I didnt bleed, cut myself and thrown blood at the car to make sure it worked properly. Blood is key to life, and without life there wouldnt be any projects to do- Therefore blood is crutial to any project you may be doing. Morbid and psychotic I know, but welcome to my world of neverending chaos and deravity!

Cain

***It is now that we battle.When you die, await my arrival in the afterlife where we will battle again.Perhaps there you may have the ability to defeat me,but not here,not now,not this day.So let us part with words and embrace the blade.***