Page 2 of 2 FirstFirst 1 2
Results 11 to 18 of 18

Thread: Grid cut-out templates.Your ideas and methods.

  1. 07-19-2007, 09:45 PM #11
    DACOTA
    DACOTA is offline
    Sith Acolyte DACOTA's Avatar
    Join Date
    Mar 2006
    Location
    The Kaleesh Warlord Temple on Kalee
    Posts
    966

    Default

    Ok sounds good,pretty simple. I'll go do it then get everything powder-coated and anodizedand you will soon see my first mhs saber.
    "aaah... general kenobi.... you are a bold one."-general grievous

    http://starwars.wikia.com/wiki/Qymaen_jai_sheelal

    Proud owner of the first two Darth Maul conversion kits! Thanks Tim!
    Reply With Quote Reply With Quote
  2. 07-19-2007, 11:04 PM #12
    Jedi-Loreen
    Jedi-Loreen is offline
    Council Member
    Jedi Council Member     Jedi-Loreen's Avatar
    Join Date
    Dec 2005
    Location
    Not of this Earth
    Posts
    6,077
    Send a message via AIM to Jedi-Loreen Send a message via MSN to Jedi-Loreen Send a message via Yahoo to Jedi-Loreen

    Default

    What parts are you planning to get powder coated?

    Keep in mind that if you powder coat anything that will be under a sink tube overlay, then that overlay may no longer fit over the parts. You're adding to the diameter slighty when you have something powder coated.
    In order to see the Light,
    you must sometimes risk the Dark.
    TCSS MODERATOR


    BLUE 8 Ready to ROCK and ROLL!
    Reply With Quote Reply With Quote
  3. 07-20-2007, 07:16 AM #13
    Hasid Lafre
    Hasid Lafre is offline
    Sith Lord Hasid Lafre's Avatar
    Join Date
    May 2007
    Location
    Nebraska
    Posts
    3,943

    Default

    Yeah but the sinktubes dont really sit very good on the mhs anyway. its alwase been sloppy for me.
    Any intelligent fool can make things bigger and more complex. - Albert Einstein

    Reaganomics not Obamanomics

    Reply With Quote Reply With Quote
  4. 07-20-2007, 08:06 AM #14
    DACOTA
    DACOTA is offline
    Sith Acolyte DACOTA's Avatar
    Join Date
    Mar 2006
    Location
    The Kaleesh Warlord Temple on Kalee
    Posts
    966

    Default

    Yeah I think a thin coat would be fine cause you can see some space in between the mhs anyways but thanks for the help,I almost missed that point.
    "aaah... general kenobi.... you are a bold one."-general grievous

    http://starwars.wikia.com/wiki/Qymaen_jai_sheelal

    Proud owner of the first two Darth Maul conversion kits! Thanks Tim!
    Reply With Quote Reply With Quote
  5. 07-20-2007, 07:41 PM #15
    Novastar
    Novastar is offline
    Council Member Novastar's Avatar
    Join Date
    Mar 2007
    Location
    San Jose / San Francisco, CA
    Posts
    4,082

    Default

    Quote Originally Posted by Hasid Lafre
    To darth dan you listen save you it can(sorry nova had to steal it from ya).
    I stole it from Yoda, so steal away...
    ~~ GREYTALE NOVASTAR (Writer, Director, Choreographer, Sound Designer, Actor, Saber Designer, Vocal Artist)
    ~~ Balance of Power, EP I: "Into The Lion's Den"
    ~~ Balance of Power, EP II: "Ashes of The Phoenix"
    ~~ The Crystal Focus Sound CD Compendiums... are HERE! ~~
    ~~ Nova & Caine's Staged Combat System... comin' SOON!
     ~~ Crystal Focus Wiring Guide
    Reply With Quote Reply With Quote
  6. 07-21-2007, 02:42 PM #16
    DACOTA
    DACOTA is offline
    Sith Acolyte DACOTA's Avatar
    Join Date
    Mar 2006
    Location
    The Kaleesh Warlord Temple on Kalee
    Posts
    966

    Default

    Btw as a side note,what do you guys think of the saber design above in my first post?
    "aaah... general kenobi.... you are a bold one."-general grievous

    http://starwars.wikia.com/wiki/Qymaen_jai_sheelal

    Proud owner of the first two Darth Maul conversion kits! Thanks Tim!
    Reply With Quote Reply With Quote
  7. 07-21-2007, 02:43 PM #17
    Stinky Bantha
    Stinky Bantha is offline
    Youngling Stinky Bantha's Avatar
    Join Date
    Jun 2007
    Location
    Location: Location:
    Posts
    200

    Default

    I think it looks great, although I'm not a fan of the blue on the grip section. It'll be tough to cut the sleeves for it though. Good luck!
    Reply With Quote Reply With Quote
  8. 07-22-2007, 02:18 PM #18
    DACOTA
    DACOTA is offline
    Sith Acolyte DACOTA's Avatar
    Join Date
    Mar 2006
    Location
    The Kaleesh Warlord Temple on Kalee
    Posts
    966

    Default

    I got it all marked just gotta cut now,oh boy.
    "aaah... general kenobi.... you are a bold one."-general grievous

    http://starwars.wikia.com/wiki/Qymaen_jai_sheelal

    Proud owner of the first two Darth Maul conversion kits! Thanks Tim!
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules