Hi all

It gets asked pretty much every day around here....

"Which degree lens should I use? What's the difference?"

Well, I'm here to help answer a few of your questions as well as dispel some of the myths you might have heard.

First off, we sell two different degree lenses here: 10 degree and 5 degree. Both work well with the standard 1" thick walled blades.
In fact, if you have a thin walled and a thick walled 1" OD blade under 30" in length, you probably won't notice much difference. It's
the longer blades and the 3/4" OD blades where you start to see one outshine the other. More on that below.

When you hear 5 degrees and 10 degrees, it's natural to think that those degrees are the angle at which the beam spreads. This is
true, but what most people do NOT realize is that a lens measures the angle that the beam spreads to ON EACH SIDE of center. That means that a 5 degree lens diverts from the center line 5 degrees on each side. That makes for a 10 degree beam, not 5 like many people assume. Same for a 10 degree lens. The beam for it is really 20 degrees.

So what does this mean to your average Luxeon saber builder? In the simplest terms, it just means that a 10 degree lens makes a fatter
beam than a 5 degree lens does. But which is better for YOU? Well, that depends on which blade you're intending on using the most. If you can visualize that the 10 degree's beam is twice as "fat" as a 5 degree, then it helps you to understand why a short thin walled blade (which has a larger internal diameter) would light up a little better with a 10 degree whereas the 5 degree would be better suited for a longer thin walled blade or a thick walled blade, which has a tighter internal diameter.
Likewise, if you are using a thin walled 3/4" OD blade, which are popular to many because of their light weight, then it makes sense that the smaller internal diameter would benefit from the tighter degree beam the 5 degree lens offers. This is only good to a point though. As with any blade, once you get so far away from the light source, the blade will dim out to the point of being too dark. Fortunately, most people don't use 4 or 5 foot blades, so it becomes a question excessive length versus even brightness.

Here is a comparison picture I took a few years ago showing how the same LED lights up the same blade differently depending on which degree lens is used. Note: I used a 6 degree lens at the time, but they are darn near identical to the 5 degree ones we now sell. The blade is a 36" thick walled model with only a single wrap of blade film. Double wraps provide more even lighting, but this shows the difference between the various lenses better. I tested a few other degree lenses at the time too:



This is a picture of a 3/4" thin walled 34" long blade using a 5 degree lens. Again, it uses a single wrap of blade film:




Now for those pesky myths you might have heard:


MYTH # 1: You don't need a lens. The LED is bright enough as is. I hear they're like a laser.

Not true. While Luxeons are VERY bright, they are not a laser and need focusing. Without a lens, the brightness cannot be focused into the blade efficiently. Bottom line: You need a lens.

MYTH # 2: All lenses are the same.

Again, not true. There are several different degrees of lenses built, but only a couple really work well for the Luxeon blades TCSS sells.

MYTH # 3: The tighter the degree, the brighter the blade.

As the previous paragraphs have said, certain blades, like a thin walled 1" OD model works better with a 10 degree. Once the blade gets over 30 to 35 inches however, you might want to consider a 5 degree to have the blade light up more evenly. You will lose base flare to some degree by switching to a 5 degree lens however, so if you like that look, you might be better with a 10 degree and limit your blade length to 3 feet or under. "Base flare" is the phenominon where the point of the blade closest to the saber is so bright, it seems to "flare" out and can actually look wider, especially in pictures.



So to recap:

1" thick walled - Generally use a 5 degree lens. A 10 degree will give more base flare if you like that look, but will not light as evenly.
1" thin walled - If under 35 inches long, use a 10 degree lens. If longer, a 5 degree might be better for you.
3/4" thin walled - Pretty much a 5 degree lens all the time. A 10 would be OK for an extremely short blade, but a 5 would be better.



I hope this helps.