Page 2 of 4 FirstFirst 1 2 3 4 LastLast
Results 11 to 20 of 33

Thread: first cfx build help

  1. #11

    Default

    Quote Originally Posted by RavenXp View Post
    the 'auxstrip=' parameter is in config.txt, and yes PIXIES is in the Extra's folder, if you are missing it you need to pull the most recent default package from the plecter site to get it. Also verify which firmware you are running, current version is 7F.
    yep i have 7F installed on my sd card, my issue now is, i have it wired up for final assembly, and the NPXL conncter is only lighting up red, and it won't light up the blade

  2. #12

    Default

    Quote Originally Posted by Blinding_Phoenix View Post
    yep i have 7F installed on my sd card, my issue now is, i have it wired up for final assembly, and the NPXL conncter is only lighting up red, and it won't light up the blade
    I forgot to mention it worked when i went to bed last night, but not when i woke up, i had it plugged in because the battery was dead, possible i fried the battery?

  3. #13

    Default

    The battery definitely sounds like it was empty.
    TCSS MODERATOR
    All n00bs READ these first (PLEASE)!!!:
    1. Forum Guidelines
    2. FJK’s “Down and Dirty” guide to Ohm’s Law

    "Yeah, yeah, I've heard it all before... you want blindingly bright, super loud, running 1138 blinkies off of the cheapest sound card you can find AND you want all of it to run on a battery the size of a dime, and run for a very, VERY long time. That one cracks me up every time..."
    My email: fjk_tcss@yahoo.com

  4. #14

    Default

    Quote Originally Posted by Forgetful Jedi Knight View Post
    The battery definitely sounds like it was empty.
    But when I plug it in the recharge port no longer kills power. I’m using the ls6 upgraded PCB

  5. #15

    Default

    Either you have it wired wrong, OR you have a short somewhere.
    TCSS MODERATOR
    All n00bs READ these first (PLEASE)!!!:
    1. Forum Guidelines
    2. FJK’s “Down and Dirty” guide to Ohm’s Law

    "Yeah, yeah, I've heard it all before... you want blindingly bright, super loud, running 1138 blinkies off of the cheapest sound card you can find AND you want all of it to run on a battery the size of a dime, and run for a very, VERY long time. That one cracks me up every time..."
    My email: fjk_tcss@yahoo.com

  6. #16

    Default

    Quote Originally Posted by Forgetful Jedi Knight View Post
    Either you have it wired wrong, OR you have a short somewhere.
    Found out the LS6 board has a short. But I have a backup board. I’m assuming I killed the battery from charging it too long. Have another battery on the way. I’m probably going to take a break for a few days to avoid pulling any hair out trying to find the issue.

  7. #17

    Default

    Quote Originally Posted by Blinding_Phoenix View Post
    Found out the LS6 board has a short. But I have a backup board. I’m assuming I killed the battery from charging it too long. Have another battery on the way. I’m probably going to take a break for a few days to avoid pulling any hair out trying to find the issue.
    That would do it.
    TCSS MODERATOR
    All n00bs READ these first (PLEASE)!!!:
    1. Forum Guidelines
    2. FJK’s “Down and Dirty” guide to Ohm’s Law

    "Yeah, yeah, I've heard it all before... you want blindingly bright, super loud, running 1138 blinkies off of the cheapest sound card you can find AND you want all of it to run on a battery the size of a dime, and run for a very, VERY long time. That one cracks me up every time..."
    My email: fjk_tcss@yahoo.com

  8. #18

    Default

    The new battery showed up and I took a break from the electronics to cut out my crystal chamber. But even with the new battery the blade won’t light up, and the the neopixel connector still only lights up red, no animations, no color change, just a static red, and now I’m completely lost on how to get it to work.

  9. #19

    Default

    Sounds like it could be a configuration issue. You would have to post your config.txt file.
    TCSS MODERATOR
    All n00bs READ these first (PLEASE)!!!:
    1. Forum Guidelines
    2. FJK’s “Down and Dirty” guide to Ohm’s Law

    "Yeah, yeah, I've heard it all before... you want blindingly bright, super loud, running 1138 blinkies off of the cheapest sound card you can find AND you want all of it to run on a battery the size of a dime, and run for a very, VERY long time. That one cracks me up every time..."
    My email: fjk_tcss@yahoo.com

  10. #20

    Default

    //CF-X Configuration - FOR LEDSTRIPS
    debug=0
    logport=0
    vol=50
    menuvol=50
    menugest=0
    trackgest=0
    fontgest=0
    beep=40
    muteb=0
    muteoff=0
    sleep=300000
    deep=50000
    qkignite=0
    orient=0
    valsnd=0
    switch=2
    offp=0
    offd=200
    onp=0
    ond=20
    swing_flow=360
    clash_flow=300
    spin_flow=400
    smooth_flow=1000
    lockup=300
    loop=1
    shuffle=2
    plilh=3400,4200
    omnisense=2000
    masterpower=100
    ledstrip=133
    auxstrip=0
    tridentstrip=0
    accentstrip=0
    dragstrip=20
    strippower=1111
    ls1_timings=350,700,24,1,3,0
    ls2_timings=350,700,24,1,3,0

    ## Motion Settings
    gate=50
    smooth_gate=50
    hclash=850
    hswing=450
    hslash=400
    hhybrid=550
    hforce=300
    hfclash=650
    hstab=500,-20,20
    hspin=750
    htwist=350
    hdrag=500,-90,0
    htemp=75
    spectrum_mode=3
    spectrum_axis=1
    field=10,10,10

    [profile=0]
    pname=standard_profile
    wakeup=1
    randc=0
    blastp=0
    random=2
    pom=0
    pof=0,45,90
    twon=0,-90,-45
    twoff=0,-90,-45
    wagon=0,-90,-45
    wagoff=0,-90,-45
    swon=0
    poi=2
    magic=0
    saberlock=0
    blastm=0
    randb=2
    shmrd=150
    shmrp=12
    shmrr=24
    shmr%=60,99
    focd=200
    focp=20
    focr=28
    foc%=60,99
    focl=1
    focb=1
    focf1=1
    focf2=1
    focf3=0
    fade=0
    flks=6
    flkd=25
    tridentflk=0
    flkon=1
    flkoff=1
    pulsed=0
    pulsel=0
    on_fade=1
    off_fade=1
    unstable=0
    style_pon=0
    style_poff=0
    style_preon=0
    style_postoff=0
    style_blaster=2
    style_lockup=1
    style_drag=2
    style_flicker=0
    style_sbright=0
    style_accents=0
    style_pixies=-1
    style_grafx1=-1
    style_grafx2=-1
    style_grafx3=-1
    style_clash=1
    style_stab=0
    over_pon=0
    over_poff=0
    pos_lockup=60
    size_lockup=40
    mapping_color=0
    mapping_unstable=1
    mapping_lockup=1
    mapping_drag=1
    mapping_flicker=0
    mapping_sbright=0
    mapping_move=80,310
    mapping_audio=8000,24000
    size_flicker=0
    pos_flicker=0
    force_flicker=127
    depth_flicker=127
    hcool=70
    lcool=0
    sparkf=120
    sparkd=10
    drift=1
    mapb=100
    mapc=70
    refreshfx=12
    bladepower=100
    omnisabers=0
    sbolt=8,20
    dbolt=40,810
    lbolt=15,30
    fbolt=1
    rbolt=10
    qbolt=50

    ## [profile=1]

    ## [profile=2]

    ## [profile=3]

    ## [profile=4]

    ## [profile=5]

    This is my config file, after I already tried formatting the sd card and reinstalling the base package

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •