My first MHS build: Brimstone

[Tom Tilmon]

brimstone.jpg

The gray will be polished aluminum, TCSS shroud material. This is only a semblance of my design. I'm not good at drawing. I can see what it will look like, but cannot portray it as well. Red will be subdued and smoked out. Black will be flat.

I have ordered my hilt parts, will order electronics as paychecks permit.
Hilt Parts List:
1 of: MHSV1 Blade Holder Style 2
1 of: Switchcraft 2.1mm Power Jack
1 of: 12mm AV switch bezel for MHSV1
1 of: 12mm Anti Vandal Momentary Red Ring Switch
2 of: Star thermal tape pad - Tri LED
1 of: Recharge port hole service (Style 1)
1 of: Machine recessed 12mm AV switch hole
1 of: MHS Sleeve material - 18"
1 of: MPS Insert style 1
1 of: Double male with slots style 3
1 of: MPS Pommel style 8
1 of: Hilt Style 1 (7" Double female threaded connector)
1 of: 1.2" Double Female
1 of: MHS choke style 1 short
1 of: MPS Clip

Chassis Parts List:
1 of: Li-Ion 18650 3.7V 2600mAh PCB Protected Rechargeable Battery Module
1 of: MHS speaker mount V5 - For 28mm Speakers
1 of: 2W 28mm Bass Speaker
2 of: Chassis Disc style 3 with holes
4 of: 2" Brass 3/16" OD spacer
10 of: 1/2" Brass 3/16" OD spacer
8 of: 3/4" Brass 3/16" OD spacer
8 of: 1" Brass 3/16" OD spacer
3 of: Acrylic Chassis Disc for NB and 18500/18650 pack - S3 (Clear)
4 of: Stainless 4-40 all thread
4 of: Brass 4-40 Hex nut
1 of: Brass 3/16" OD tube
1 of: Kill plug style 2
Plus various and sundry brass greeblies and doohickies from Home Crepot.

Full Disclosure: I will be using NEC Spark Color 2. I know that TCSS board users predominantly use Plector Labs Boards. I will try a Plector Labs Board in my next build (Graflex); however, I know NEC boards from 2 previous installs on the Hasbro Kylo Ren Lightsabers. So I was afraid to leave my comfort zone. I do want to get to know Plector Boards for possible future ventures.


This is MHS. I plan on this being RGB with a Crystal Chamber that matches blade color. The crystal chamber will be exposed near the top of the emitter in its own chassis system. I'll wait until TCSS gets their laser back up and running to use TCSS chassis parts. Will probably radiatorize the crystal chamber. Using a clear quartz crystal with 5mm RGB. I am going to use a 18650 pack and recharge port. The downfall, and necessary evil of my Kylo conversions were removable battery for quick change outs at cons. Its a downfall, because the shuttling in and out of the chassis puts great strain on the wiring system. When I button this one up, I want it to remain buttoned up, unless I desire to change things around on the SD card. I did some color blending on my second iteration of Kylo, but this will be my first RGB. I'm very excited to get this build going.

I have been stalking this board forever. I recently converted 2 Kylo Ren Hasbro sabers. Those conversions were each different with different aspects on each. This build is fairly complex; however, nothing more difficult than I already accomplished in both my conversions. This will be a slow build process, but I will try to document updates in this thread.

Wish me luck. If I can pull this off, I'll be pretty proud of my skillsets.

Tom