Page 1 of 2 1 2 LastLast
Results 1 to 10 of 11

Thread: NBv3 w/ 3-pin Quick Connect Wiring Check

  1. #1

    Default NBv3 w/ 3-pin Quick Connect Wiring Check

    Hello everyone. This is my first attempt ever at putting a saber together. Can someone please verify if this setup is correct?

    Things to note:
    - 3.7V battery
    - Removable battery setup
    - Act. switch LED is wired to Deep Sleep Power Indicator. Is this correct/best for removable battery setup to reduce battery drain since no kill key?
    - All dots/points = connections. If no dot (especially where wires overlap each other), not a connection.
    - I screwed up drawing the speaker wiring, got distracted...
    IMG_20160605_223813788.jpg

  2. #2

    Default

    I see no issues with that. You're correct with deep sleep but another option would be to wire the switch led in parallel with the blade then it would only light when activated.





    Edit: typo
    Last edited by Greenie; 06-06-2016 at 11:33 PM.

  3. #3

    Default

    Hey fellas, new here (first post) I have a similar question regarding NBV3. I am trying to wire a 3W LED for a crystal chamber. Can I use Power Indicator wiring for this? (Think I read in manual that there are no special accent LED leads on the NBV3.) If I understand it correctly will this light up the crystal when the blade is on?
    Thanks for the help....Chris

  4. #4

    Default

    ^^as above^^. Wire in parallel with the main LED.

  5. #5

    Default

    Why are you using a high-power LED for the crystal chamber? The answer is no, the accent pads are for accent leds that draw 18mA not 1000mA like the high intensity blade LEDs. Typically the chambers are lit with 3mm, 5mm, or SMD LEDs.
    Last edited by FenixFire; 06-06-2016 at 01:29 PM.

  6. #6

    Default

    Quote Originally Posted by Greenie View Post
    I see I issues with that. You're correct with deep sleep but another option would be to wire the switch led in parallel with the blade then it would only light when activated.
    Good point! I'm assuming that the LED ring would light up if it had been attached to Deep Sleep once awoken?

    On another note, I'm now reconsidering the recharge port. So... back to redrawing...
    Last edited by fdesa12; 06-11-2016 at 06:40 PM.

  7. #7

    Default

    I'm an idiot. The LED for chamber is 3mm (not 3W, that would be crazy, lol.)

  8. #8

    Default

    When attached to the DS pad, the LED is simply on when the saber is idle or ignited, and off when the saber is in deep sleep mode or the power is cut. So it's an ideal place for your crystal chamber LEDs if you'd like.

  9. #9

    Default

    Quote Originally Posted by NanoRex View Post
    When attached to the DS pad, the LED is simply on when the saber is idle or ignited, and off when the saber is in deep sleep mode or the power is cut. So it's an ideal place for your crystal chamber LEDs if you'd like.
    I'm thinking I will attempt that on my next build. The size of the pad intimidated me on the first NB build. I have an Idea to have the chamber lit dimly from the DS pad. Then fire a second accent wired with the blade on ignition. Might even just do it on my latest build as it is still unfinished, and I already have the extra 3 mm installed in the chamber.

  10. #10

    Default

    That's a really cool idea. If you had room, you could even wire a third white LED in parallel with the FoC for added effect.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •