Missing anything?

[Asydbern]

Picked up some extra stuff just in case. Don't think I missed anything. Gonna be my first build
Bryon



47OHM1/2W .47ohm .5w resistor 5 $0.45
2AA 2AA Battery holder 1 $1.20
PXT Power Xtender? 2.0 1 $6.11
T8TG9 9" Electronics shield for 1.25" ID tubes 2 $2.00
DF7F Hilt Style 5 (7" Fluted double female threaded connector)
Machine recessed 16mm AV switch hole
1 $29.00
MPSI1 MPS Insert style 1 1 $5.50
Cclip MPS Clip 2 $0.75
MPS3v2 MPS Pommel style 3 v2 1 $23.75
Holder18 MHSV1 Blade Holder Style 18
MHS Heat Sink V4 (Flat Style)
1 $37.25
LaserWork Acrylic Chassis Disc 2 hole to 3 hole adapter - S9 (Blue) 2 $2.99
LaserWork Acrylic Chassis Disc for NB and 18500/18650 pack - S3 (Blue) 3 $3.99
NBHWH3 NB V2 MWS Header and Wiring Harness 1 $1.99
LaserWork Acrylic Chassis Disc for Recharge Port - S8 (Blue) 2 $3.99
BR316N Brass 4-40 Hex nut 10 $0.15
ST440AT Stainless 4-40 all thread 3 $2.75
CD2 Chassis Disc style 2 2 $3.75
STTAPE Star thermal tape pad 3 $1.00
TRSL 18deg Tri-Rebel/Cree Star Lens 1 $2.25
CTCLED Custom Tri-Cree LED
** SinkPad Copper tri-cree star pad
Royal Blue Cree Die
White Cree Die
Royal Blue Cree Die
1 $24.00
8323TSR 8-32 x .3" red thumb screw 1 $2.25
TWShow LED Trans White Show blade 1" OD (36 inches)
** 1" Thin walled Trans White PolyC 40" long (No)
** Blade Assembly
** White Standard
1 $18.75
8323TSBLU 8-32 x .3" blue thumb screw 1 $2.25
Film Blade film (Double wrap +$3.00, 1" Thin walled) 1 $7.50
BR316T Brass 3/16" OD tube 2 $5.99
BASSSPKR 2W 28mm Bass Speaker 1 $6.50
SPKRV5 MHS speaker mount V5 - For 28mm Speakers 1 $5.50
DynaOhm 20mA DynaOhm? Variable Resistor 1 $2.63
.5OHM3W .5ohm 3w resistor 5 $0.75
1ohm2w 1ohm 2w resistor 5 $0.66
1/16Heat 1/16" Heatshrink tubing 2 $0.50
1/8Heat 1/8" Heatshrink tubing 2 $0.50
3/16Heat 3/16" Heatshrink tubing 2 $0.50
3/32Heat 3/32" Heatshrink tubing 2 $0.50
26Black 26 gauge wire (sold by the foot) (Black) 10 $0.25
26Blue 26 gauge wire (sold by the foot) (Blue) 10 $0.25
26Brown 26 gauge wire (sold by the foot) (Brown) 10 $0.25
26Green 26 gauge wire (sold by the foot) (Green) 10 $0.25
NanoBisc Nano Biscotte Sound Module V2
NB sound module base unit
Nano Biscotte V2 Sound Module SD card
1 $65.00
26Orange 26 gauge wire (sold by the foot) (Orange) 10 $0.25
26Grey 26 gauge wire (sold by the foot) (Grey) 10 $0.25
26Red 26 gauge wire (sold by the foot) (Red) 10 $0.25
26White 26 gauge wire (sold by the foot) (White) 10 $0.25
26Yellow 26 gauge wire (sold by the foot) (Yellow) 10 $0.25
2.1PlugAdapter 2.1mm plug adapter for smart charger 1 $2.50
KPLUG4 Kill plug style 4 1 $1.25
SCJACK Switchcraft 2.1mm Power Jack 2 $2.75
JSTCP JST connector kit male and female 6 $0.50
Grease Super Lube Synthetic Grease 1 $0.40
SMRNW 16mm Anti Vandal Short Momentary White Ring Switch 1 $12.00
26Purple 26 gauge wire (sold by the foot) (Purple) 10 $0.25
PAN18650P Panasonic Li-Ion 18650 3.7V 3400mAh PCB Protected Rechargeable Battery

[Jay-gon Jinn]

I think you've got everything you'll need there....I have to wonder about the 2-AA battery holder, unless it's for something else. (An 18650 will not fit in there...it's far too big.) you won't need a battery holder with the chassis discs anyway. also, the Corbin blade film doesn't really work very well with the Transwhite blade stock...you'd be better off just using clear gift wrap for that instead. Your chassis disc style 2's you have listed look like the ones without holes, was that what you wanted?

[Asydbern]

The battery holder is just to put some alligator clips on for testing various things with a low current 3v source. And yes I know the chassis disks are blank. Basically all of the aluminum disks were out of stock. Thanks for looking it over, package arrives Wednesday and I really can't wait to get started. Good to know about the blade film. I went back and forth between the trans white tccs style blades endlessly. Ultimately decided on the trans white because I read a lot of posts where people said that blue looked best in it. I'll add the film to the spare parts pile for the next build.
Bryon