need another set of eyes to double check please

[snilam]

SaberBuilder_render.jpg
SaberBuilder_render2.jpg
SaberBuilder_render3.jpg

leaving out stull like wire and shrink tube, powder coating
Also there is no LED sourcing that elsewhere

PLI
LED "TCSS style" Show blade 1" OD
Star thermal tape
4" Double Female Grooved
MPS Pommel style 7
.75" Male / Female extension X4
Double male with slots style 3
MHSV1 Blade Holder Style 19
3" Double female threaded connector
Trim Ring 3
Chassis Disc style 4
Stainless 4-40 all thread X3
Brass 3/16" OD tube
Brass 4-40 Hex nut
MHS speaker mount V4 - For 28mm Speakers
7.4v Li-ion 2600mAh 18650 Battery Pack
Acrylic Chassis Disc for PC 2.0 and 18500/18650 pack - S2 (Clear) X2
8-32 x 1/8" Set screw
8-32 x 1/4" Brass button head screw X35
MHS Sleeve material
12mm Anti Vandal Momentary Purple Ring Switch
12mm Anti Vandal Momentary Green Ring Switch
MHS "new style" Heat Sink V3
MPS Clip
Brass MPS Insert style 1
2W 28mm Bass Speaker
Petit Crouton Sound Module V3
Petit Crouton V3 Color Xtender
Chassis Disc style 5
Super Lube Synthetic Grease
USB to 3.5mm R.I.C.E.? cable
7.4V Li-ion smart charger with 2.1mm plug
Kill plug style 5 (Gold)
2.1mm Power Jack
3.5mm R.I.C.E.? Port Style 1

As far as services go I'm have some PC done and 2 av switch recess holes done. Question I need the power jack hole machined but I don't see that service in the store. Anyone know where it is or what it is under? I'm drill and tapping my own blade retention since I have that already. As far as the color xtender mounting goes I'm just going to order 2 sets of the Acrylic Chassis Disc for PC 2.0 and 18500/18650 pack - S2 (Clear) and just use the second set to hold my color xtender and glue it down since the disc cut out is to big. Does anyone else have a better suggestion for that? The LED I'm going to use will be a tri cree RGrB also.

If anyone sees anything I missed or any suggestions let me know. Thanks everyone!

[Silver Serpent]

The Nano Biscotte discs would be better for holding the Color Xtender. You'll need some needle files to widen it a bit, but it'll work.

The internals look fine. You seem to have everything covered. I'm curious why you have so many of the 0.75" extensions? I would just use a single larger double female, with a double male adapter instead. If there's a specific reason for it, that's fine. I am just not certain why you are going that route.

[amwolf]

In place of all those extentions,why not go with a (fill in overall extension length here for the piece behind the blade holder and the slotted element), ask Tim to cut grooves to match (how far) from one end; go with a standard extention in place of all those 3/4" pieces; and use a gender changers (can even be JBWelded into place) as needed? Just a thought...

[snilam]

Ah yes nb avrylics, thanks for the tip . As far as the 4 small extensions go, they are going to be seperated by one of the 3 trim rings and on each one im going to get engraved or acid etch the code of the jedi. Im only doing 4 instead of 5 because at Mara Jade's funeral they only list 4, and while it is not a Mara hilt it is definately Mara inspired. Still not sure if im going to do the whole code or just key words onto each section. Its kinda like for a jedi who has a battle going to the dark side in their head and need this constant reminder.

[Silver Serpent]

That sounds like a perfectly legitimate reason. Good luck with your build!

[snilam]

If I would have seen all those extensions I would be like what the hell man. Probly should have said something about why all the extensions. Sorry guys