how bout a all red enginled to a US2 soundboard? how, if possible, would it wire up?
how bout a all red enginled to a US2 soundboard? how, if possible, would it wire up?
Lan-Ed-Tul
The Brotherhood Of The Sith
SL 6208 501st legion & SLD
TK-6208
You dont know the POWER, of the dark side.......
Proud member of the FSM!!
Hey Fenderbender,
When you wire the RGGB that way, what batteries are you using? I want the same color scheme and I was lucky enough to get one of the latest Crystal Focus boards. I really dig your Narada Blade colors of a Cyan bin 1 blade with the orangish FOC, I saw it on another blade in the gallery. Too Cool.
Thanks
In 90% of my builds I use 14500s. In most of my/customer's designs, those are the cells that fit....*shrugs*
Run time isn't so hot (20-40min depending on set up), but most people don't use them for more than that on a charge unless you're a trooper or a regular CON'er. Then, you'd have some decisions to make regarding space and runtime vs. design.
If you're new, please take the time we all consider just as precious as you and READ!
GET LATHED!
Official BMF and LORD OF THE STRINGS
still needing to know how a all red engineled wires to a UltraSound one or two soundboard. i mainly need to know for a US2, its in my Vader heiland synchronar flash handle saber. i have a lux 3 red/orange in there now, and if it ever goes out, i need to know how one of these leds wire up to it.
Lan-Ed-Tul
The Brotherhood Of The Sith
SL 6208 501st legion & SLD
TK-6208
You dont know the POWER, of the dark side.......
Proud member of the FSM!!
Hi FenderBender, i will make my first saber with the Power Xtender and i want to use the red or deep red LEDengin; you said you have post info on the differences between red and deep red have you do that ? i don't find it on the forums
Hey guys, I am about to order all the parts to make my saber and I have one last question about the LEDEngin Die. I want a blue saber with an angry orange FOC. Couldn't I user a RGGB and wire the blue by it self for the main blade and then and RG for the Flash on Clash?
Thanks for the input..
You can wire it that way, but remember that the flash color will also blend with the blade color. You'll end up with R, G, and B all illuminated during the flash.
We all have to start somewhere. The journey is all the more impressive by our humble beginnings.
http://led.linear1.org/1led.wiz for the lazy man's resistor calculator!
http://forums.thecustomsabershop.com...e-to-Ohm-s-Law for getting resistor values the right way!
Yes, it will be mostly white with a little bit of an orange tint. For brightness, I would wire the B and G together for a Skyblue, and then use the R and G for flash. Brighter blade, nice clash=win.
If you're new, please take the time we all consider just as precious as you and READ!
GET LATHED!
Official BMF and LORD OF THE STRINGS
Just want to double check my calculations. So I got a CF from a recent run and wants to do a FoC set-up with a LedEngin RGGB.
I plan to run GG in parallel at 2A and will be using the Red for a yellow FoC. What I want to know is what current should I run the Red at? 1500 or 1000? If I were to run it at 1500 that means my resistor wattage should be 7.4-3=4.4 x 1.5 = 6.6W. Since Sunrider said it's ok to use 1/4 of the recommended wattage for FoC setup, am I right in assuming that a 1.5W to 2W resistor should be sufficient? Thanks
Bookmarks