Getting there....I need to route the wires to allow for more movement in the sensors...
Getting there....I need to route the wires to allow for more movement in the sensors...
Knowledge must be balanced by Practice.
Practice must be balanced by Experience.
Through Knowledge, Practice, and Experience
we gain Wisdom.
-Boj-Vaati Mau
Jedi Sentinel, Jar'Kai practitioner,
and Instctor at Strafe Plains Temple
Saber Guild: Strafe Plains Temple
The Rebel Legion
Got the emitter stabilized with the help of Milliput. Now I've just got to knock it back out as I managed to short the Blade LED somehow while working a non-TCSS clear poly tube to fit.
Knowledge must be balanced by Practice.
Practice must be balanced by Experience.
Through Knowledge, Practice, and Experience
we gain Wisdom.
-Boj-Vaati Mau
Jedi Sentinel, Jar'Kai practitioner,
and Instctor at Strafe Plains Temple
Saber Guild: Strafe Plains Temple
The Rebel Legion
And I'm calling it good at this point.
Time to move on to my wife's build...
Knowledge must be balanced by Practice.
Practice must be balanced by Experience.
Through Knowledge, Practice, and Experience
we gain Wisdom.
-Boj-Vaati Mau
Jedi Sentinel, Jar'Kai practitioner,
and Instctor at Strafe Plains Temple
Saber Guild: Strafe Plains Temple
The Rebel Legion
Well now, after a few months of Golden Gate Knights and some fairly hard dueling with Demon Bunnyman I've decided to pull the PC from this saber. I want to convert it to a stunt with recharge. Does this schematic look right?
Last edited by Boj-Vaati Mau; 07-30-2012 at 02:00 PM.
Knowledge must be balanced by Practice.
Practice must be balanced by Experience.
Through Knowledge, Practice, and Experience
we gain Wisdom.
-Boj-Vaati Mau
Jedi Sentinel, Jar'Kai practitioner,
and Instctor at Strafe Plains Temple
Saber Guild: Strafe Plains Temple
The Rebel Legion
That schematic looks fine to me
Click here to learn all about me!
The Shoutbox: The only place you can double post!
Anybody who spells it Lightsabre is dyslexic
"Yeah, if I had Skotts face I'd hit it too" ~ Fenderbender
"You didn't buy a toy saber just to break it. You bought an economy sound card with a really complicated wrapping scheme." ~ Silver Serpent
RewireofDarthYoda.jpg
I think this way may work a little better. You'd need a kill key to turn it off the way you had it wired.
We all have to start somewhere. The journey is all the more impressive by our humble beginnings.
http://led.linear1.org/1led.wiz for the lazy man's resistor calculator!
http://forums.thecustomsabershop.com...e-to-Ohm-s-Law for getting resistor values the right way!
Helps to have teh fulldiagram of the switch...
Knowledge must be balanced by Practice.
Practice must be balanced by Experience.
Through Knowledge, Practice, and Experience
we gain Wisdom.
-Boj-Vaati Mau
Jedi Sentinel, Jar'Kai practitioner,
and Instctor at Strafe Plains Temple
Saber Guild: Strafe Plains Temple
The Rebel Legion
If you push the switch, you're gonna short your two battery terminals together. The switch connections (C and NO) go on positive OR negative, not one of each.
The switch LED is fine.
We all have to start somewhere. The journey is all the more impressive by our humble beginnings.
http://led.linear1.org/1led.wiz for the lazy man's resistor calculator!
http://forums.thecustomsabershop.com...e-to-Ohm-s-Law for getting resistor values the right way!
Oh....duh! It's a DPDT...just have to think of it as two slide switches. Makes sense again, thank you sir.
Knowledge must be balanced by Practice.
Practice must be balanced by Experience.
Through Knowledge, Practice, and Experience
we gain Wisdom.
-Boj-Vaati Mau
Jedi Sentinel, Jar'Kai practitioner,
and Instctor at Strafe Plains Temple
Saber Guild: Strafe Plains Temple
The Rebel Legion
Posting Permissions
Reply With Quote
Bookmarks