Page 1 of 10 1 2 3 ... LastLast
Results 1 to 10 of 92

Thread: Commonly used Drill bits, taps, and measurements

  1. #1
    Jedi Council Member cardcollector's Avatar
    Join Date
    Jan 2009
    Location
    I am A proud American.
    Posts
    2,567
    Blog Entries
    3

    Default Commonly used Drill bits, taps, and measurements

    Hey all,

    I decided that since I was compiling a list of common measurements I used, I thought it would make a great thread to have various drill bit used for switches, taps, etc...

    So here is what I have so far. If you would like a measurement, post it up.

    Drill bits, taps, and screws
    For the Basic Switch
    - Use a 3/8” bit for hole
    - Or use a 1/2” bit for countersink

    For the Lighted 16mm anti-Vandal Switch
    -To tap and thread; 15mm bit w/ M16-1 tap
    -Use a 23/32 endmill to countersink the AV switch. Drill a 5/8" hole first.

    For the Gaurded Switch
    - If you want to use the retaining nut; 1/2" bit
    - For a force fit; 7/16” bit. 11.5mm bits work well also.

    For the Small Momentary Switch
    - To tap and thread; M5x0.5 tap with a 4.5mm bit

    2.1mm Recharge Port
    - To tap and thread; 5/16-32 tap (M8x.75 metric tap) & 9/32” dill bit

    For the 5mm LED bezel
    - To tap and thread; M8x0.75 metric tap & 7.25mm Drill bit. 5/16-32 tap is not compatible with the Bezel

    For the T1 LED Indicators
    -To tap and thread; M6 x0.75 metric tap & 5.25mm Drill bit

    For R.I.C.E. Port Style #1
    -To tap and thread; M6x0.5 metric tap & 5.5mm bit

    For R.I.C.E. Port Style #1
    -To tap and thread; M8x0.75 metric tap & 7.25mm Drill bit. 5/16-32 tap is not compatible.

    Silver Tactile switch
    -To snugly mount, use a 13/64" bit.




    For 4-40 screws
    - 4-40 tap with a 3/32" bit OR #43 drill bit

    For 6-32 screws
    - 6-32 tap with a 7/64" bit OR #36 drill bit

    For 8-32 screws
    - 8-32 tap and 9/64" bit OR #29 drill bit

    For 10-32 screws
    - 10-32 tap and 5/32" bit OR # 21 drill bit

    Allen wrench Sizes
    Hex size for socket head cap screws:
    #2 - 5/64"
    #4 - 3/32"
    #6 - 7/64"
    #8 - 9/64"
    #10 - 5/32"
    #12 - 5/32"

    Hex size for button head cap screws:
    #2 - .05"
    #4 - 1/16"
    #6 - 5/64"
    #8 - 3/32"
    #10 - 1/8"
    #12 - 5/32"

    Hex size for set screws:
    #2 - .035"
    #4 - 05"
    #6 - 1/16"
    #8 - 5/64"
    #10 - 3/32"

    Use as a guideline only.


    Here are some measurements...

    1.5” 22 gauge sinktube
    -OD- 1.5”
    -ID- 1.45”

    1.25” 22 gauge sinktube
    -OD- 1.25”
    -ID- 1.20”

    MHS Main body/double female connector/MHS to 1.5" adapter
    - OD- 1.45"
    - ID- 1.25"

    Useful charts for taps and drill bits

    Metric http://www.engineersedge.com/manufac...rill-chart.htm

    ANSI http://www.engineersedge.com/tap_drill_chart.htm


    I know this is by no means complete, so feel free to add to the list!
    Last edited by cardcollector; 06-01-2012 at 08:11 PM.
    Got a Question? There's a thread for that...
    ~Do what you can, with what you have, where you are.~Teddy Roosevelt

    SollusVir everywhere else... FXsabers, Youtube, etc...

  2. #2

    Default

    Good idea. I would love to be more helpful but I don't have access to any saber stuff during the weekdays.

    Can't forget our good friends in the blade retention/screw department.
    8-32 tap, 9/64 bit

    MHS mainbody/double female connector/ MHS to 1.5 sinktube adapter
    1.45" OD
    1.25" ID
    (not sure how accurate this is but it's a must)


    The other common screw sizes would be a nice addition too.
    4-40, 6-32, 10-32

    Accent LED holders would be the last common thing I can think of.

  3. #3
    Force Aware Nineteen's Avatar
    Join Date
    Oct 2008
    Location
    Northwest Missouri
    Posts
    115

    Default

    Another useful note would be which allen wrenches go with what screws. I know I often forget, and need to ask someone.
    "The man in black fled across the desert, and the gunslinger followed."

  4. #4
    Jedi Council Member cardcollector's Avatar
    Join Date
    Jan 2009
    Location
    I am A proud American.
    Posts
    2,567
    Blog Entries
    3

    Default

    Added crystal.

    Keep them coming!
    Last edited by cardcollector; 07-13-2010 at 06:10 AM.
    Got a Question? There's a thread for that...
    ~Do what you can, with what you have, where you are.~Teddy Roosevelt

    SollusVir everywhere else... FXsabers, Youtube, etc...

  5. #5

    Default

    *votes for sticky*
    Every time Tim ships an order... an angel gets its wings



    "Just get one and go nuts, that's how this hobby works. Get stuff. Go nuts. Period." ~FenderBender~

  6. #6

    Default

    For 6-32 tap. drill size should be #36.

    Hex size for socket head cap screws:
    #2 - 5/64"
    #4 - 3/32"
    #6 - 7/64"
    #8 - 9/64"
    #10 - 5/32"
    #12 - 5/32"

    Hex size for button head cap screws:
    #2 - .05"
    #4 - 1/16"
    #6 - 5/64"
    #8 - 3/32"
    #10 - 1/8"
    #12 - 5/32"

    Hex size for set screws:
    #2 - .035"
    #4 - 05"
    #6 - 1/16"
    #8 - 5/64"
    #10 - 3/32"

    These hex key sizes were pulled from a screw catalog I have and I have not taken the time to physically verify every one is correct. Use as a guideline only.


    The 'correct' tap size for the recharge port is M8x.75 This is a metric tap. and it's Imperial equivalant is .315 - 33.87 - so it is very close to a 5/16 - 32.

    On the 5mm LED bezels, I know the tap size for the cone shaped bezel is also M8x.75. I have not had the opportunity to purchase a low profile domed bezel yet to verify it's thread but I suspect it is also M8x.75.

    Interestingly, the nuts that come on the 5mm cone type LED bezel and the 2.1mm recharge ports are interchangeable. However the LED bezel will not screw into a 5/16-32 threaded hole but the recharge port will. It probably has to do with the way they are manufactured and how loose the tolerances are.

  7. #7
    Council Member
    Jedi Council Member
    Rhyen Skytracker's Avatar
    Join Date
    Feb 2009
    Location
    Covington, GA
    Posts
    2,550

    Default

    Here is the sizes needed for the T1 LED indicators http://www.thecustomsabershop.com/Gr...tor--P495.aspx

    Tap M6 x .75 metric
    Drill bit 5.25 mm

    Also, the drill bit needed for the M8 x .75 that acerocket mentioned above is a 7.25mm bit.
    Last edited by Rhyen Skytracker; 07-13-2010 at 10:38 AM.

    Live long and...I mean May the force be with you. http://saberconcepts.50.forumer.com/index.php

  8. #8
    Council Member
    Jedi Master
    FenderBender's Avatar
    Join Date
    Jul 2008
    Location
    Earth System - Rhode Island
    Posts
    1,531

    Default

    Also, the force fit on the guarded switches work better with a 11.5mm bit/end mill

    To counter sink an anti-vandal 23/32 end mill with 5/8 hole.

    If you're new, please take the time we all consider just as precious as you and READ!

    GET LATHED!

    Official BMF and LORD OF THE STRINGS

  9. #9
    Council Member
    Jedi Council Member
    Rhyen Skytracker's Avatar
    Join Date
    Feb 2009
    Location
    Covington, GA
    Posts
    2,550

    Default

    Here are some drill and tap charts that I use:

    Metric http://www.engineersedge.com/manufac...rill-chart.htm

    ANSI http://www.engineersedge.com/tap_drill_chart.htm

    This is turning out to be a very helpful thread and I think it should be a sticky thread.

    Live long and...I mean May the force be with you. http://saberconcepts.50.forumer.com/index.php

  10. #10

    Default

    This is an awesome and USEFUL thread to have this all in one place.

    *seconds the suggestion for a 'sticky' on this*

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •