Search:

Type: Posts; User: Forgetful Jedi Knight

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. The sound drop isnít that noticeable, but your...

    The sound drop isnít that noticeable, but your mileage may vary. Itís been fine for me.

    i havenít had any issues after the fact, but then again, I know what Iím doing when building sabers, so I...
  2. Replies
    5
    Views
    54

    For the Red, most likely. Blue and Green should...

    For the Red, most likely. Blue and Green should be ok. How (or more importantly where) to wire it depends on what else you have going on in your hilt.
  3. Replies
    1
    Views
    36

    You do not need 15A draw batteries for a CFv7,...

    You do not need 15A draw batteries for a CFv7, and the answers to the rest of your questions can easily be found in the CFv7 manual.
  4. Replies
    37
    Views
    1,978

    22 gauge is fine.

    22 gauge is fine.
  5. Poll: Sounds like you have some type of switch issue...

    Sounds like you have some type of switch issue (not wired properly, misconfigured, etc).
  6. Poll: What kind of build is this one? Another Tri-Cree?

    What kind of build is this one? Another Tri-Cree?
  7. OK, I reopened it. Let me know if you have any...

    OK, I reopened it. Let me know if you have any issues/need any help.
  8. Which topic is locked? I can unlock it for you.

    Which topic is locked? I can unlock it for you.
  9. Replies
    37
    Views
    1,978

    Did you check to make sure the battery is fully...

    Did you check to make sure the battery is fully charged first?
  10. Replies
    20
    Views
    478

    Putting it where you had it, the holes will...

    Putting it where you had it, the holes will likely be blocked by the heatsink module, sooooo.....
  11. Replies
    20
    Views
    478

    If youíre trying to put speaker holes in the...

    If youíre trying to put speaker holes in the choke, you should put them towards the bottom, where the sound is actually coming from.
  12. Replies
    20
    Views
    478

    It would be weak, probably look bad and would...

    It would be weak, probably look bad and would probably fall off with contact
  13. Replies
    9
    Views
    694

    Sounds like a dead battery to me.

    Sounds like a dead battery to me.
  14. Replies
    20
    Views
    478

    I doubt youíll ever achieve something like that,...

    I doubt youíll ever achieve something like that, youíd have to have custom work done on a choke like that with predrilled holes for the rods, and even THEN, Iím not sure if it would work or look...
  15. Replies
    1
    Views
    129

    A very light green.

    A very light green.
  16. Poll: Make the following change: strippower=0000

    Make the following change: strippower=0000
  17. Replies
    37
    Views
    1,978

    You have to know what version of firmware you...

    You have to know what version of firmware you have on your card before you just go randomly adding parameters.
  18. Poll: Please post your main configuration file.

    Please post your main configuration file.
  19. Poll: You either have a faulty recharge port, charger...

    You either have a faulty recharge port, charger OR there is a wiring issue with your recharge port.
  20. Replies
    2
    Views
    227

    You could use it, itíll just take some work to...

    You could use it, itíll just take some work to get it to work the way you want it to IIRC.
  21. Replies
    6
    Views
    1,044

    The V2 can withstand combat, as long as you build...

    The V2 can withstand combat, as long as you build them properly. Also, you can get switch holes just about anywhere, just ask and be specific (additional charges apply).
  22. The stock boards can’t handle a Tri-Cree (it can...

    The stock boards can’t handle a Tri-Cree (it can support one of the three die) and no, I don’t believe you can add FoC to a simple board like that.
  23. Replies
    5
    Views
    1,105

    You have to make sure that the LEDSTRIP= number...

    You have to make sure that the LEDSTRIP= number is approximately how many pixels you have in your blade, not “0”.
  24. Replies
    37
    Views
    1,978

    The CFX is normally set to run with a 3.7V...

    The CFX is normally set to run with a 3.7V battery. If you used any of the 7.4V from the store, they donít put out anywhere near enough amperage to run 2 Neopixel strips.
  25. Rob and I discussed the CFX video before I even...

    Rob and I discussed the CFX video before I even did it. Since he didnít have the time to do it, and I did, you guys got me for that one.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4