Search:

Type: Posts; User: welshm85

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    3,745

    MHSv1 speaker and 2x AA battery holder

    http://https://www.thecustomsabershop.com/MHSv1-speaker-and-2x-AA-battery-holder-P766.aspx
    Is this compatible with the aa dummy cell to use with a 14500 3.7v battery?
  2. The Nephews’ sabers are installed and awaiting shipping

    17266
  3. Replies
    7
    Views
    3,899

    Thanks!

    Thanks!
  4. Work in Progress MHS sabers for the nephews!

    17234
    One will be purple and the other blue. Both loaded up with NBv3s!
  5. What does the switch look like? I just converted...

    What does the switch look like? I just converted my BS Luke and have the switch from that.
  6. Replies
    7
    Views
    3,899

    Do you know where this video is located? I looked...

    Do you know where this video is located? I looked at his youtube channel and didn't see it.
  7. Replies
    0
    Views
    349

    BS ANH Luke conversion kit screw

    I need to replace the small screws that came with my ANH Luke conversion kit. It looks to be - 4-40 button head.
  8. Replies
    2
    Views
    3,204

    My cellophane was only so wide. So I had to cut...

    My cellophane was only so wide. So I had to cut it to length. I did this twice hence the 2 layers. I added a third wrapped layer and it is much better.
  9. Replies
    2
    Views
    3,204

    Trans White Blade

    I have added 2 layers of cellophane to my thin walled trans white blade, but it still appears to be see through. Can I add another layer or should I sand the blade?
  10. Replies
    8
    Views
    1,108

    Looks sweet!

    Looks sweet!
  11. Replies
    8
    Views
    1,024

    Damn, that looks great!

    Damn, that looks great!
  12. Thread: Another build

    by welshm85
    Replies
    5
    Views
    808

    Another build

    Here is a recent build that I did that is TCW Ahsoka based.
    I purchased a sink knob from Lowes and epoxied it to the pommel #1.
    16972
    I painted it to match my shroud.
    16973
    Here is the saber...
  13. Replies
    0
    Views
    392

    Activation box style 12

    I have Activation box style 12 and Activation box style 13. I am not going to be using a rice port or a or switch 20. My question is can I fit an accent led in these holes?
  14. Thread: Wiring help

    by welshm85
    Replies
    17
    Views
    2,016

    Thank you FJK for sharing this. I knew I saw...

    Thank you FJK for sharing this. I knew I saw something somewhere in relation to Ohm's law but couldn't find it.
  15. Thread: Wiring help

    by welshm85
    Replies
    17
    Views
    2,016

    I have used 1 ohm 2 watt resistors for my reds in...

    I have used 1 ohm 2 watt resistors for my reds in the past while running off of a 3.7 volt.
  16. Thread: Wiring help

    by welshm85
    Replies
    17
    Views
    2,016

    This (http://led.linear1.org/1led.wiz/) is the...

    This is the calculator that I use.
  17. Thread: Wiring help

    by welshm85
    Replies
    17
    Views
    2,016

    That depends on the led and your battery. What is...

    That depends on the led and your battery. What is your battery set up?
  18. Thread: Wiring help

    by welshm85
    Replies
    17
    Views
    2,016

    If you are going to swap the led out, I would see...

    If you are going to swap the led out, I would see if you could get the resistor pre-wired on to the module above the jst connector.
  19. Replies
    3
    Views
    923

    Do we have access to the copper heat sink he is...

    Do we have access to the copper heat sink he is talking about with out the module.
  20. Thread: Wiring help

    by welshm85
    Replies
    17
    Views
    2,016

    I can see that. Especially if you wanted to swap...

    I can see that. Especially if you wanted to swap the led color between say, red and blue.
  21. Thread: Wiring help

    by welshm85
    Replies
    17
    Views
    2,016

    But to answer you main original question, yes you...

    But to answer you main original question, yes you will need a resistor for a red led. I'm sure you have utilized a resistor calculator and have come up with the necessary resistor.
  22. Thread: Wiring help

    by welshm85
    Replies
    17
    Views
    2,016

    Since you will have to solder the board anyway,...

    Since you will have to solder the board anyway, why not just get the led, module, heat-sink, and lens separately?
  23. I'm sitting on some MHSv2 parts that I was...

    I'm sitting on some MHSv2 parts that I was thinking of doing a combination saber similar to what you are describing. I have the MHSv2 6", 5", 3" and 2-2" extension pieces. I like the idea of being...
  24. Thread: Rose Gold

    by welshm85
    Replies
    4
    Views
    2,873

    That looks really sweet!

    That looks really sweet!
  25. Replies
    6
    Views
    4,085

    They announced it on facebook. Here is the link....

    They announced it on facebook. Here is the link. https://www.facebook.com/163181440369599/photos/pcb.1969961256358266/1969958636358528/?type=3&theater
Results 1 to 25 of 49
Page 1 of 2 1 2