You would have to sand the diameter of the FX blade to fit inside the TCSS hilt as the FX blades are a slightly bigger diameter than the TCSS parts.
Type: Posts; User: pandatrooper
You would have to sand the diameter of the FX blade to fit inside the TCSS hilt as the FX blades are a slightly bigger diameter than the TCSS parts.
Try Hyperdyne or Romfx Revo.
I have but I used a brass pipe section as an overlay for the activation box that was the length of the box.
Argh...
OK, I just tried wiring up the SPST blue illuminated switch via the L1 pad on the US 2.5 and the LED did not light up. I figured it's not powerful enough, so I tried to wire it directly...
Thanks for the feedback guys! I didn't know the resistor chart on the TCSS site had illuminated switches (they're at the bottom of the drop down) and I was able to figure out what resistor was...
I was able to do something similar. I used the ribbed extension with a sink tube on top but the switch is not held in with the nut on the inside. I used a box 9 switch bezel so that it bolts on from...
Hi everyone. I tried searching and didn't find what I needed so I am posting this up.
I had a US 2.5 that I bought way back and never installed it. Finally dug it up and put it in my TCSS hilt...
Fantastic work! Love the step by step pics. You are a true craftsman!
Point taken. But I wasn't thinking that it would be a "drag and drop solution", I was just thinking that the technology exists, and that perhaps the tunability option could be there on saber version...
I know it's not the exact same thing, but the guy that develops Rom FX for Stormtrooper / Vader voice changer boxes is coming out with a board that allows you to adjust tone / pitch,...
I've got a few sabers from other companies, and they pale in comparison to TCSS sabers in terms of quality, customizability, service, etc..
I've placed multiple orders in the span of 3 months,...
I think my clever bit of Photoshopping actually caused more confusion. :)
I didn't flip the orientation of the ribbed section, it's exactly as it is in the shop MHS builder. This diagram should...
Yes, you still use a lens and lens holder. If you're using a MHS blade holder, you can use a lens (the "Luxeon" collimator) and and the "Luxeon" lens holder on the P4. I ordered them and they fit,...
I don't think I'm cutting into any threads on the extension or ribbed section. Please correct me if I'm wrong.
Maybe this diagram will clarify? The ribbed section goes into the 5" extension like...
I'm planning on using a guarded momentary on this one. I figured the threads on the switch are long enough and I don't mind guarded switches. Plus the switch and collar are above the point where the...
Wow, that's super impressive! Nice work on the saber too BTW :)
I guess I probably been more clear. I've attached an image below of the rough layout.
I want to use a 5" extension as the lower body of the hilt, then a ribbed section. At the base of the rib...
Awesome, thanks for the speedy reply :)
Just want to make sure these will fit before ordering. Will a 4AA holder fit in a 5" extension with a speaker holder? In the shop, it says the 4AA holder will fit in a standard main body, but I can't...
I'm using the little round bezel. A squre washer inside is a great idea! Thanks for the tips guys, much appreciated.
Some are selling for $250 on ebay. Craziness!
Maybe try the Blaster builder club forums for more info? They should be able to help.
http://www.imperial-fleet.com/BBC/community/
I don't follow the games that much but I think there's 2 different ones. Here's some pics I found
http://images3.wikia.nocookie.net/starwars/images/f/f0/Nihilus_saber.jpg
...
OK, I know there must be some kind of silly trick for this that I'm just not getting.
I'm installing an AV switch into a hilt (going to use a connector to make wiring easier) but how on earth do...
Now you are prepared at all times, even when jogging! :)
http://www.anythingbutipod.com/archives/2010/01/star-wars-lightsaber-mp3-player.php
...