Search:

Type: Posts; User: Rayataz

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds; generated 44 minute(s) ago.

  1. Thread: NBv4 placement

    by Rayataz
    Replies
    2
    Views
    2,669

    Thanks FJK!

    Thanks FJK!
  2. Thread: NBv4 placement

    by Rayataz
    Replies
    2
    Views
    2,669

    NBv4 placement

    In previous iterations of Plecter Labs sound boards, many of their manuals state that it is usually a good idea to keep the placement of the soundboard closer to the pommel or at least 1" from the...
  3. Replies
    0
    Views
    1,406

    CF8 PLI settings

    Okay, so I've set up a Crystal Focus 8 saber using the accented LEDs for the first time but I am a little confused as to programming the PLI during the lockup phase.

    Wiring and Setup
    So I've...
  4. Replies
    6
    Views
    3,941

    Thanks for the suggestions, guys! I might try a...

    Thanks for the suggestions, guys! I might try a few more times to ensure all the surfaces are covered and letting the solvent sit momentarily before putting it together. I may also give Tim's...
  5. Replies
    6
    Views
    3,941

    How do I know if I'm not using enough? Or if I'm...

    How do I know if I'm not using enough? Or if I'm applying it correctly? The liquid tends to ooze out of the sides once I've put it on the end of the blade and pushed the tip into blade.
  6. Replies
    6
    Views
    3,941

    Blade tip falls off during sparring

    Hey guys,

    I've had a number of blades where their tips tend to fall off after a duration of medium-to-hard dueling. I've been using a 16 acrylic cement...
  7. Replies
    2
    Views
    1,718

    Of course! I don't know why I didn't notice that...

    Of course! I don't know why I didn't notice that before when I first read the manual. Thanks Rob! :)
  8. Replies
    2
    Views
    1,718

    Idle glowing and activated crystal LED?

    Hey there,

    I had a question regarding if it is a good idea to wire up a crystal RGB LED on a Crystal Focus v8 to both the accented LED pads as well as the main color channels. My intention is...
  9. Replies
    3
    Views
    1,662

    Thanks Hermitjensen! I was about to post my...

    Thanks Hermitjensen! I was about to post my schematic when I took a closer look at it and figured it out! I misread the manual and wired the ignition ground directly to the auxiliary switch instead...
  10. Replies
    3
    Views
    1,662

    Okay.... so I removed the auxiliary switch from...

    Okay.... so I removed the auxiliary switch from the circuit and just plugged in the latching ignition switch and the sabers turn on normally. Is this pointing to a wiring issue with the switches?
  11. Replies
    3
    Views
    1,662

    Trying to diagnose failing ignition

    Hey guys,

    I'm trying to diagnose a problem with my PC PRIZM. When I connect my board to a 3.7v battery, it boots up normally but it will not ignite. My setup currently has the PC connected to a...
  12. Thank you! This was very informative!

    Thank you! This was very informative!
  13. On the CF power requirements and battery life

    Hey guys,

    I've been tinkering around with an idea for a new saber that I want to work on. And in doing so, I've been trying to figure out the power requirements for a CF 7.5 and what the best...
  14. Replies
    12
    Views
    4,500

    Hmm. I'm probably going to start with the Teflon...

    Hmm. I'm probably going to start with the Teflon tape first and move on if the solution isn't adequate. Thanks for all the ideas, guys!
  15. Replies
    12
    Views
    4,500

    Blue loctite is non-permanent? Hmm, I will try...

    Blue loctite is non-permanent? Hmm, I will try that first.
  16. Replies
    12
    Views
    4,500

    Will do! Thank you! :)

    Will do! Thank you! :)
  17. Replies
    12
    Views
    4,500

    I mostly have issues with it coming un-screwed...

    I mostly have issues with it coming un-screwed between the main body and the choke since that's where my grip is especially when I execute spins.
  18. Replies
    12
    Views
    4,500

    Will this also keep the pieces "glued" together?...

    Will this also keep the pieces "glued" together? If so, it might be less than ideal if I need to open them up for maintenance or repair.
  19. Replies
    12
    Views
    4,500

    Securing MHS parts together

    Hey guys,

    Is it recommended to drill a threaded hole through the threaded parts of the MHS pieces? I've noticed that during dueling, the MHS parts tend to unscrew themselves a little and it gets a...
  20. Replies
    9
    Views
    3,926

    Wow. That's beautiful! Good job!

    Wow. That's beautiful! Good job!
  21. Replies
    9
    Views
    3,070

    Easiest fix ever! Thanks again! :lol:

    Easiest fix ever! Thanks again! :lol:
  22. Replies
    9
    Views
    3,070

    Okay. I think I'll do that. Thank you! :)

    Okay. I think I'll do that. Thank you! :)
  23. Replies
    9
    Views
    3,070

    Do I just put solder between those two pads?

    Do I just put solder between those two pads?
  24. Replies
    9
    Views
    3,070

    Okay. Having a "feeling like an idiot" moment...

    Okay. Having a "feeling like an idiot" moment here lol but what exactly am I supposed to do to bridge those pads?
  25. Replies
    9
    Views
    3,070

    I'm not entirely sure what the resistor pad on...

    I'm not entirely sure what the resistor pad on the PEX is but I'm going to gander a guess and say no presumably since nothing looks bridged at this point
Results 1 to 25 of 61
Page 1 of 3 1 2 3