Search:

Type: Posts; User: FencerScott

Search: Search took 0.00 seconds.

  1. Thanks, BZWingZero! I'm assuming that the...

    Thanks, BZWingZero! I'm assuming that the external switch will bypass the switch on the card? Looking at the card, it appears that SW1 has a positive and negative hole. Being that I'm putting in a...
  2. Let's try that again .......

    Let's try that again ....
    http://i296.photobucket.com/albums/mm200/FencerScott/temporary_zpsi3m63lsq.jpg
    http://i296.photobucket.com/albums/mm200/FencerScott/temporary_zpsl67sppep.jpg
    ...
  3. Switch problem on the Hasbro econo board. Help!

    Morning all!

    I recently got hold of a Luke Skywalker lightsaber on ebay. Pulled it apart, found everything pretty much as described on the tutorials, so I was pretty happy. Until I discovered...
  4. Replies
    9
    Views
    4,834

    I don't think I have ever seen a more awesome...

    I don't think I have ever seen a more awesome blade holder! Well done!
  5. Replies
    3
    Views
    2,410

    I realize this is a bit late, but another...

    I realize this is a bit late, but another technique to bend PVC is to cap the end, fill the pipe with sand, and then use your heat gun. The sand dissipates the heat and helps keep the bend even.
  6. Replies
    2
    Views
    5,345

    First (ish) PVC Saber Build

    After a couple of false starts, I finished my first PVC saber. It's a simple dueling saber, with a 3W Lux Blue Rebel running off 4AA. I wanted to see if I could engrave into PVC, then touched up...
  7. Replies
    4
    Views
    5,358

    Thanks, Silver and BZWingZero. This really helps...

    Thanks, Silver and BZWingZero. This really helps a lot!
  8. Replies
    4
    Views
    5,358

    But it is still pretty easy to figure out the...

    But it is still pretty easy to figure out the layout and solder in the new led, speaker, transistor, etc?
  9. Replies
    4
    Views
    5,358

    Newer Hasbro economy sound question

    Hi all. Hopefully I am placing this question in the right place. If not, please forgive me!

    I was in Target the other day, saw the $19.99 sabers, and thought of adding sound to my current build....
  10. Replies
    12
    Views
    9,986

    If you don't mind me asking, I was looking again...

    If you don't mind me asking, I was looking again at your tutorial for PVC sabers for children. You run a Rebel star at 350ma off 2 AAA with a resistor. TCSS says amber lux rebels should be run at...
  11. Replies
    12
    Views
    9,986

    Oh, my bad. I found both of them almost at the...

    Oh, my bad. I found both of them almost at the same time. Must have been confused. Sorry. :(
  12. Replies
    12
    Views
    9,986

    They must have. I found it here: ...

    They must have. I found it here:
    https://www.pinterest.com/pin/470204017320571862/
  13. Replies
    12
    Views
    9,986

    Thanks so much! You're saving me a ton of grief...

    Thanks so much! You're saving me a ton of grief and money in ordering parts. So, if I build with a Li-ion pack, I'll need to work in a recharge port, too, right?

    I'm marking off places for set...
  14. Replies
    12
    Views
    9,986

    AAA battery holder question

    Hi all, I'm a first time builder. I'm so glad I found this forum! But there's one question I can't find the answer to, either here or on the TCSS store page.

    I'm using 1" pvc pipe for the...
Results 1 to 14 of 14