Search:

Type: Posts; User: darth_chasm

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Lack of response is due to the forums going...

    Lack of response is due to the forums going pretty quite overall in the last 2 years or so.

    I haven’t done a setup like this so haven’t really checked the manual. The battery can deliver 15A when...
  2. A chassis’ purpose is to hold your components...

    A chassis’ purpose is to hold your components securely to prevent damage, prevent shorts, ensure proper operation, facilitate good wire management, etc. A cardboard tube would provide none of this.
    ...
  3. That would be better. People have made pvc...

    That would be better. People have made pvc chassis in the past. Some very reputable smiths at that.
  4. Not advisable at all. Use a proper chassis...

    Not advisable at all. Use a proper chassis solution. The store sells everything you need. You don’t necessarily have to use a 3D printed solution.
  5. Sorry you mentioned the specs In the first post....

    Sorry you mentioned the specs In the first post. The new speaker you ordered has a higher power rating so you are ok there. It has a lower resistance which means more current will flow through...
  6. Did it come with a manual or specs that could...

    Did it come with a manual or specs that could tell you what speaker can be used? Or, does the old speaker have rating markings on it?

    I know absolutely nothing about those sabers.
  7. Replies
    4
    Views
    278

    Nice! I didn't see that. That would definitely be...

    Nice! I didn't see that. That would definitely be better!
  8. Replies
    4
    Views
    278

    I believe the only one that locks in place is...

    I believe the only one that locks in place is this one but it is for MHS V1 https://www.thecustomsabershop.com/MHSv1-NeoPixel-Hilt-Side-Adapter-V2-P1341.aspx

    For the one you have you could do a...
  9. Replies
    5
    Views
    365

    Post high quality, close up photos of the board,...

    Post high quality, close up photos of the board, both top and bottom.

    Is your battery charged? Is your board secure from ambient vibration?
  10. no sweat

    no sweat
  11. I didnt read this whole thread so if this is out...

    I didnt read this whole thread so if this is out of place I apologize. But NB doesn't support the use of an Aux switch...
  12. Replies
    4
    Views
    502

    You need to find the specs of the led so that you...

    You need to find the specs of the led so that you can identify the forward voltage of the diodes. Then using that info, the battery voltage and ohms law you can determine your required resistance....
  13. I’m afraid I don’t live there anymore and I’m not...

    I’m afraid I don’t live there anymore and I’m not close. Otherwise I’d consider it.

    side note, Mark Hamill is filming there currently.
  14. Replies
    2
    Views
    2,681

    If you are referring to the longer, pre-wired...

    If you are referring to the longer, pre-wired "assembly" then no. It is not representative of all NB v4's. That is a custom board that was designed exclusively for TCSS. The differences between it...
  15. Replies
    3
    Views
    573

    Accent Pixel should do the trick. I personally...

    Accent Pixel should do the trick. I personally would wire it parallel to the blade. It's the diagram that appears above the one you posted here.
  16. Ha!! This is my hometown.

    Ha!! This is my hometown.
  17. Replies
    3
    Views
    722

    Welcome My gut tells me that if there is any...

    Welcome

    My gut tells me that if there is any change it will be negligible. Yeah, we use mirrored blade tips for in hilt leds but in that case the light is pointed directly at the reflective...
  18. Replies
    6
    Views
    904

    Thanks for the kind words guys!

    Thanks for the kind words guys!
  19. Replies
    3
    Views
    609

    Welcome back! Yeah, the hobby has changed quite a...

    Welcome back! Yeah, the hobby has changed quite a bit. Even in the time I've been active it has changed.

    CFX can run on 3.7v now without any hacks. You'll want to go with the high drain 15A cell....
  20. Replies
    6
    Views
    904

    Thanks SS. Long time no speak. Hope you're doing...

    Thanks SS. Long time no speak. Hope you're doing well.
  21. Replies
    1
    Views
    545

    you can charge one

    you can charge one
  22. Replies
    6
    Views
    716

    I think you might need to connect L3 to the...

    I think you might need to connect L3 to the Negative of the connector as well. I may be wrong so if someone knows otherwise please chime in. Also, did you order it set up for neopixel? There's a...
  23. Replies
    6
    Views
    904

    DCLS-006le #1

    I'm sure many have seen it already elsewhere, but TCSS was key in getting this done so I need to post this here as well. This is the refinement of the prototype design from a couple of years ago.
    ...
  24. Replies
    7
    Views
    1,362

    I've used 6-32 before that have worked ok for...

    I've used 6-32 before that have worked ok for light sword play. IDK, maybe others can chime in on the 4-40. It's just that the nose on those has such a small point of contact.
  25. MHS discs have 2 holes because thats what works...

    MHS discs have 2 holes because thats what works with MHS parts and MHS parts are not the same dimensions as a Graflex. So there is really nothing there making things complicated.

    Have you, by...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4