Search:

Type: Posts; User: cvsickle

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    2,043

    Powder coating is available in the services...

    Powder coating is available in the services section of the shop. The powder coating in the builder is incredibly outdated and doesn't include MANY/MOST of the available colors.
  2. Replies
    8
    Views
    1,549

    Correct.

    Correct.
  3. Replies
    3
    Views
    535

    I see. I don't know what your hilt restrictions...

    I see. I don't know what your hilt restrictions are, but you're probably going to want to adjust the design of your hilt internals to accommodate a larger battery.

    Even if you find a 10A 18500...
  4. Replies
    3
    Views
    535

    You'll want to get the 10A or 15A 18650 from the...

    You'll want to get the 10A or 15A 18650 from the store. The standard ones can't draw enough current (in general) for a fully lit Neopixel blade.
  5. If you use an NB or a Prizm (both 3.7v), you'll...

    If you use an NB or a Prizm (both 3.7v), you'll have to wire the two greens in parallel, so you'll have less run time. If you use a CF (7.4v), you can wire them in series, so you won't notice a...
  6. I'd still try a faster SD card to see what...

    I'd still try a faster SD card to see what happens.
  7. Ok, another question: did you remember to...

    Ok, another question: did you remember to reformat the SD card before moving all of the sounds over to it?
  8. Does this occur on all sound banks? Just asking...

    Does this occur on all sound banks? Just asking to make sure it's not the boot sound that is being used.

    Probably more helpful discussion: are you using the SD card that came with the soundboard?...
  9. Replies
    6
    Views
    1,338

    The TRA forums will probably be your best bet. FX...

    The TRA forums will probably be your best bet. FX Sabers is also an option, but traffic there seems to be waning.
  10. Replies
    9
    Views
    1,380

    The honest answer to your question is: I don't...

    The honest answer to your question is: I don't really know. I'm not quite as happy with the etch on the shroud (I left it in too deep), but I was impressed with how well the grip piece turned out....
  11. Replies
    4
    Views
    3,709

    The Nano only has 10 bit audio while the Prizm...

    The Nano only has 10 bit audio while the Prizm has 16 bit. The Prizm WILL sound better, but it all depends on who you ask as to HOW MUCH it sounds better. Some people will not even notice a...
  12. Replies
    9
    Views
    1,380

    Thank you! I think the lower grip turned out...

    Thank you! I think the lower grip turned out pretty good. The shroud etching got a little deeper than I was hoping for, though. Lesson learned on that one. Haha
  13. Replies
    9
    Views
    1,380

    Yep, I remember when you made that video. The...

    Yep, I remember when you made that video. The method I came up with to get the switches on the other side of the heat sink is probably less eloquent than whatever he does, but it works. lol
  14. Replies
    9
    Views
    1,380

    Contempt - an MHS saber. (PIC HEAVY)

    One of my first memories in the saber building community was stumbling on to Rob (madcow) Petkau's YouTube channel. I sat an watched almost every single one of his videos and I was absolutely amazed...
  15. Replies
    2
    Views
    556

    You're going to want the 10A 3200 mAh battery....

    You're going to want the 10A 3200 mAh battery. The 3400 doesn't have as high an output current, which is required for the Neopixels.
    ...
  16. Replies
    8
    Views
    2,146

    Yep. That's it. What I've done in the past is...

    Yep. That's it. What I've done in the past is bridge all three positive pads on the LED star with very short wires and then just run one wire from one of the pad since I connected all of them....
  17. Replies
    8
    Views
    2,146

    Better, but I would still put the resistors on...

    Better, but I would still put the resistors on the negative wires rather than the positive ones, like Tom suggested. Effectively, it will work the same either way, but putting them on the negative...
  18. Replies
    2
    Views
    629

    There are places online where you can have a...

    There are places online where you can have a chassis for that particular hilt 3d printed. I won't post a link because this forum is attached to a store, but you can find it by searching on Google or...
  19. Replies
    8
    Views
    2,146

    Someone on Reddit had this same diagram (probably...

    Someone on Reddit had this same diagram (probably the same person). I told them the same thing you did. No response there yet. Hopefully they see this feedback before they wire up that resistor...
  20. Ok make sure that's your setting. The second...

    Ok make sure that's your setting. The second number in drive and fdrive is there value for L2. If that seeing doesn't work, then you probably have wiring problems.
  21. Change fdrive to 1023,1023,0 and leave drive and...

    Change fdrive to 1023,1023,0 and leave drive and focmix where they are. Make sense?
  22. Replies
    13
    Views
    1,559

    Yes, the 1023 just applies the max voltage of the...

    Yes, the 1023 just applies the max voltage of the battery to the pad. Any lower value just applies the proportional voltage.
  23. Replies
    13
    Views
    1,559

    You'll have to set the drive parameter in your...

    You'll have to set the drive parameter in your config to have L1 and L2 on full with the fdrive adding L3 as a flash on clash die. My advice is to look through the sections of the NB manual regarding...
  24. Replies
    3
    Views
    843

    The diode is supposed to get the forward voltage...

    The diode is supposed to get the forward voltage up closer to what a blue or green die uses.
  25. Replies
    3
    Views
    843

    Custom Vestige Saber

    Hey all,

    I purchased an empty Vesitge hilt by 7 Chambers from a member of another forum a few weeks ago. It is a customized version of one of their production sabers.

    I installed it with a Nano...
Results 1 to 25 of 172
Page 1 of 7 1 2 3 4