Are you copying files from one CFX compatible font to another CFX compatible font? Or are you trying to replace specific files with custom made other files to use instead? You have to make sure the...
Type: Posts; User: Zzan
Are you copying files from one CFX compatible font to another CFX compatible font? Or are you trying to replace specific files with custom made other files to use instead? You have to make sure the...
since you used an inline resistor on the data line did you bridge the SMD pad on the board? If not you have no connection From page 34 of the manual:
For space saving, we have included a 0603...
This sticky might help shed some light on how to paint/bake to make it stick and last longer.
Can you successfully save an edit with the card inserted into a PC/Mac? The reason I ask this is that I have a few older micro SD cards laying around that are stuck in "Read Only" mode. I can...
Dremel off a little bit at a time being careful to not damage remaining threads until you get it to the length that provides enough tension to hold the blade and is still screwed in far enough to...
I typically use header pins and sockets. They are super cheap, small, and you can get them in any number of pins/sockets combinations. If you have ever built your own PC this is what is used to...
I would remove the chassis disk style 5 and replace the speaker holder with a v5 which has a lip to lock it in place between pommel and hilt. Then just run your rods directly into the speaker holder...
As long as the board isn't damaged it shouldn't be too hard for you to clean it up remove all the solder and wire and then wire it up correctly. The wiring diagrams can be found in the manual which...
There are 4 posts on a lit AV switch. 2 for the switch which just as with any other momentary doesn't matter which post is which it is just interrupting a circuit. The LED posts are + and - and you...
As rlobrecht mentioned runtime is the biggest difference. Also if you plan on dueling with the saber I would stay away from battery holders and just wire with a recharge port -- see Madcow's videos...
Probably the easiest way is to touch the + and - for the die with your 3.7v battery for a sec to see what color it is Both of those colors have a max voltage higher than that so you shouldn't have...
I use an X-Tronic dual station. It has tweezers on the left and an iron on the right. Came with brass sponge, magnifier light, replacement heating element, variety of tips. Digital controls can be...
Does your custom made Chassis hold the board in the center of the MHS hilt? or is the battery underneath it making the board close to the inside of the hilt? Make sure the board and its contacts...
My kids brought home a flyer from their school where some group was teaching saber combat with lightsaber replicas as an after school activity. This is in the Tampa - Plant City, FL area. I didn't...
Good luck :)
You should check out the R2 Builder's Club.
You can download plans, talk to other builders etc. A lot like this site except all about R2 units :)
It's a fun but VERY expensive...
Are your pads just bridged or are there actually SMD resistors there? Do you have a pic?
If they are just bridged then you can inline wire your resistor.
Compare the one you got off your chassis with the ones that fit. Is there a major difference or is it just minor that you could fix with some sandpaper around the edges of your discs?
The attached store sells these things so we will not recommend other products from other vendors as that is against the rules of this forum.
In the matter of 3400mah vs 2600mah. The larger the...
I don't think you can attach that blade holder to a sink tube. You may want to pick a MHS V1 Main Hilt/body and Pommel and pommel insert. You will also want to check the box for the MHS Heatsink...
No problem. Glad it was something relatively easy to fix :)
Did you bridge the SMT pads for the accent LEDs? If you use inline resistors the SMT pads need to be bridged to complete the connection.
This is the only thing I see wrong with your diagram. If you...
Do you have a wiring diagram that you followed, so we can look to see if any obvious mistakes were made?
Do you have pics of your wiring/soldering so we can see if there might be a short or mistake?...
What I would suggest is go to the store and compare the pictures of the Corbin Style Show Blade and the TCSS style show blade in the complete blades section. The Corbin style uses the blade film the...
The Trans White is a white blade not something that goes inside another blade. It is simply a opaque white blade as opposed to the clear polycarbonate of the first blade listed.
You likely don't...
Should only need pins one and five.
14590
Though I think you should take Avidgrant's suggestion and put a switch between the port and the electronics so that you can prevent charging and/or...