Search:

Type: Posts; User: 174fps

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    7,629

    Just got word from Naigon... 4-8 ohms work...

    Just got word from Naigon...

    4-8 ohms work fine, so 2 8ohm in parallel would be okay. 2 4 ohm in parallel would be bad :)
  2. Replies
    12
    Views
    7,629

    I would check with Naigon as the manual doesn't...

    I would check with Naigon as the manual doesn't list what impedance it is capable of handling. You have to be careful with paralleling drivers as you will increase the load on the audio amp. Be...
  3. Replies
    5
    Views
    5,116

    Like any speaker out there, it will work just...

    Like any speaker out there, it will work just fine whether wired correctly or wired backwards. If wired backwards however, phase/soundstage/spectral balance etc will be completly out of alignment. ...
  4. Replies
    5
    Views
    5,116

    The 2w bass speaker I have does list polarity on...

    The 2w bass speaker I have does list polarity on the magnet. For the premium speaker, I use a PV battery and touch the terminals and see which direction the speaker moves. If it goes out, then the...
  5. Replies
    10
    Views
    5,719

    Sounds like a job for an EZ out screw extractor....

    Sounds like a job for an EZ out screw extractor.

    Best of luck in getting it out!
  6. current = brightness only to a point. Each LED...

    current = brightness only to a point. Each LED is different, and you risk either blowing or shortening the lifespan of an LED if you feed it too much current. LEDEngin's are great for overdriving...
  7. Replies
    6
    Views
    3,120

    Yup, very helpful.

    Yup, very helpful.
  8. Replies
    12
    Views
    20,745

    Awesome and very detailed!

    Awesome and very detailed!
  9. Nope not a CF, it starts with an I.... Using a...

    Nope not a CF, it starts with an I....

    Using a switch to separate the colors seems flawed. If you were able to separate the colors via a switch, you would only have the three to choose from. Any...
  10. I have that exact setup on my latest build, but...

    I have that exact setup on my latest build, but using a different board altogether. This board allows the use of any color for blade/clash when connected in this manner. It's a no-no here to...
  11. The PWM leg is the output of the transistor to...

    The PWM leg is the output of the transistor to the right of the FoC pad. See below for a photo of the FoC pad connection, and the second yellow line is where you would connect the PEX to the PC 2.0...
  12. Is there a benefit of running the 2 series dice...

    Is there a benefit of running the 2 series dice on the PC at only 1.5A, when you can run it at 2A? Runtime...or LED lifespan perhaps?
  13. Replies
    0
    Views
    1,832

    PC 2.0 SD Card Holder - Lifted from board

    Hey Everyone,

    I have not read about this problem on the forum so thought I would share an issue I had this week with my PC 2.0 and its SD card holder. My setup utilizes a floating card, and after...
  14. Sticky: Update... So I hooked up the unit to my PC...

    Update...

    So I hooked up the unit to my PC this evening and was indeed able to get a color difference with a 10 ohm resistor on a parallelled G+B setup. There seems to be pretty bad color...
  15. Sticky: Okay, well right now I have a parallelled setup...

    Okay, well right now I have a parallelled setup with B+G connected to a PC 2.0. I tried putting a pot on the blue die today with the hopes it would affect the color and then I could meter the pot,...
  16. Sticky: Thanks for responding Jay I always appreciate...

    Thanks for responding Jay I always appreciate your input.

    I am doing a static test at the moment, but plan on connectiing this to a PC 2.0 board or possibly my igniter R2 (although that one I can...
  17. Sticky: HI there, I have an RGBW that I want to...

    HI there,

    I have an RGBW that I want to resistor to cyan, and am a little fuzzy on how to accomplish this. I have tried both series and parallel wiring, and when I add extra resistance to either...
  18. Sticky: 7154Hey everyone! So on Kevin's advice I...

    7154Hey everyone!

    So on Kevin's advice I contacted Erv and got some infor on the Full Powah setup for PC/PEX 2.0...

    Per Erv'
    "Wiring on a PC 2 is exactly as on the PC1, the control wire goes...
  19. Replies
    24
    Views
    10,181

    Does anyone know where I can find a wiring...

    Does anyone know where I can find a wiring diagram for a full powah setup for the LEDengin and PC 2.0? If one does not exist I should be able to get by if someone can help me out with the signal...
  20. Very well done! I may have to steal some of your...

    Very well done! I may have to steal some of your concealment methods for my upcoming build...

    Where did you come across the nylon washers and tubes to go over the 4-40 rods?
  21. Sticky: Does anyone have a Full Powah setup diagram for...

    Does anyone have a Full Powah setup diagram for the PC 2.0? I've looked through many threads but cannot find one. I am a little suprised this is not included in the PC manual.

    Or if there is one...
  22. Blade pics and descriptions

    7006

    Here is the red polyC tube (40" thick-walled) I spoke about earlier with 6' of gift wrap. I had to use a P4 white in it as my RRRR has not yet arrived. I think the look is quite good, and...
  23. Hey there everyone, I was racking my brain...

    Hey there everyone,

    I was racking my brain trying to find my personal preference for blade type/thickness/film use etc for some time. I am still waiting on a few corbin blades with my next order,...
  24. Replies
    83
    Views
    30,360

    How does one send attachements inside a message...

    How does one send attachements inside a message here? I only see URL links in the PM or "send email" section, and the Insert file option does not allow me to select from computer, again only URL. ...
  25. Replies
    24
    Views
    10,181

    Has anyone had any issues with the 18mA accent...

    Has anyone had any issues with the 18mA accent LED output from the PC 2.0? I would like to use these outputs for my AV LEDS as well as my crystal chamber, and in both cases, the current rating of...
Results 1 to 25 of 34
Page 1 of 2 1 2