Search:

It is really a matter of opinion on whether the 2W bass is better. Sure it has more low end and headroom but the volume pales in comparison to the premium speaker. I had the 2W in my Luke V2 for a...

Well Tim, I asked a few weeks back via email if the acrylic disk will fit a CF5.10 and you wasn't sure. I went ahead and order the discs anyway and well they do fit a CF5.10 perfectly. I am really...

Need more info.

Where did you mount the PC? What sound font are you using? What is this beep that you are talking about because the PC shouldn't be beeping if all files are present.

Also, you...

At this point, you will need to tear the PC apart, might be a grounding issue or something.

Do charged the batteries and try again. I had sabers acting weird before due to low bat.

If that didn't work, remove the board and only wire the speaker and battery pack and see it is powers on.

Did you use the lens with a lens holder or not? I noticed the ledengin works better without a lens holder. Just let the lens rest directly on top of the dome. Also, try using a standard mid grade...

I think what IA is trying to say here is that a touch activation switch is nothing new. Parks has been using them for a while now.

That depends on how many mA you are running the FoC die at. According to the resistor calculator here http://led.linear1.org/1led.wiz, if you run R and B in series at 1500mA, you should be using 2W...

My resistor is the small one since I am only running one die. But since the FoC is only on for a short duration it is possible to get away with one that is 1/4 of the needed wattage. For example,...

I upgraded my V2 recently to CF5 and Led Engine RGGB so I believe I can help you.

Firstly, I am assuming that you know which pads powers which LED. Once you know which is which it's quite simple....

I believe a p4 blue can take 1.5A since i have seen a few builds here doing that.

Just want to double check my calculations. So I got a CF from a recent run and wants to do a FoC set-up with a LedEngin RGGB.

I plan to run GG in parallel at 2A and will be using the Red for a...

I actually sealed mine in heatshink and then stuck them into the hilt held by double sided tape. Work perfectly so far.

With a deep red led you can definitely get away with one 3.7v li-on since red only needs like 2.5v to power.

This is still an ongoing debate until today but it's actually fine to used a single 3.7V li-on for the PC. LDM and many other builders have done so.

LDM did it for his MKVI run and it's green and...

Looks great Caine!!! Any reason why you didn't utilized the FoC function? Also is it possible to do a fullpowah setup using a PC1.5?

What does one do when the pad comes off? The PCB is ruined? I am curious cause my next order will be LEDENGINE RGGB.

Not trying to be obvious but the PC doesn't work without the SD card inside. If you reinsert the SD card and it still doesn't work then you might have shorted the board somehow when you pushed the...

Looks fantastic Wade. One of your best work yet.

I faced a similar problem as you. Funny that we both made a very similar looking saber.

http://a6.sphotos.ak.fbcdn.net/hphotos-ak-ash4/311973_10150368231626328_553221327_8457331_1855471803_n.jpg...

I can't help but admire your RG and Explorer at the back. Is that RG an MTM model?

Personally I made sled out of PVC. Cheaper than cannibalizing a flashlight and works the same.

It's normal. Last time I requested powder coating, the order took about three weeks to ship. If you just make normal order, it will usually ship in a day or two.

Flash on Clash (TM) here I come!!!

I run Rebel Green and P4 Green on my Luke V2 with a PC. Both will run fine and both looks great although I am more partial to the P4 shade. I fell that it is more accurate.