Search:

Type: Posts; User: Whiskey2015

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    7,671

    Hello everyone, here is a little update: ...

    Hello everyone, here is a little update:

    another NBV4 works without any problems with the same wiring in the same saber. On the board where the problem occurred, is now also the AMP defective. I...
  2. Replies
    8
    Views
    7,671

    The inner tube, that Hold the Electronics, is...

    The inner tube, that Hold the Electronics, is completely from plastics. No Chance to produce a short, that way.

    The Board is slightly! shrinked in, just it can't strip off. And the Contacts are...
  3. Replies
    8
    Views
    7,671

    Update: if I set "offd" to a value below 10,...

    Update: if I set "offd" to a value below 10, there seems to be no problem anymore.

    Except that sometimes I turn off the Saber at the "Swirl from inverted". ��

    I tested the wiring completely,...
  4. Replies
    8
    Views
    7,671

    I've tested a few more: Error occurs when...

    I've tested a few more:

    Error occurs when Saber was in Deep Sleep mode. When I reboot the saber by Killswitch a few times, suddenly it works. And if once it has worked, it will continue to work....
  5. Replies
    8
    Views
    7,671

    I know. But no Matter how long I hold the switch...

    I know. But no Matter how long I hold the switch down, the saber won't turn off.
  6. Replies
    8
    Views
    7,671

    NB mostly won't turn off

    Again this annoying guy from Germany. 🙄

    I have just completed my first saber with a NB4. and I'm really excited. except for a little problem. It can only be turned off sometimes. I usually hold...
  7. Replies
    2
    Views
    7,553

    I packed it in shrink tubing and wrapped it with...

    I packed it in shrink tubing and wrapped it with foam. So I pushed it all the way back into the hilt. Now I can reach the SD card if I unscrew the Pommel.
  8. Replies
    8
    Views
    12,206

    Ahh, good to know! NB arrived yesterday, and...

    Ahh, good to know!

    NB arrived yesterday, and of course can't wait to wire it.

    It works! Swing, Foc, on-off sounds. everything works. I am really excited. Now I have to see how I get it all...
  9. Replies
    8
    Views
    12,206

    Ahh, thats it! I use a Cree XP-E, red: 500mA,...

    Ahh, thats it!

    I use a Cree XP-E, red: 500mA, 2,1V, 625nm

    This Question I asked to me before...Better to calculate with average Current (3,7V) or fully load (4,2V)?
  10. Replies
    2
    Views
    7,553

    NB fix it in DIY Hilt?

    Hello @all,

    I'm new at the saber-scene and ordered a NB for my DIY saber. Today the Package arrived in Germany, an I wonder how I should fix the Bord inside the Saber.

    SD-Card on one side,...
  11. Replies
    8
    Views
    12,206

    Hi Tom, Thanks for your Reply, good to know...

    Hi Tom,

    Thanks for your Reply, good to know not to be the only old man here. ��

    My calculation for the Resistor follows the Instructions in NB Manual. So it will be interesting, wheres my...
  12. Replies
    8
    Views
    12,206

    Hello from Germany & first Question

    Hello everyone,

    I'm new here in the forum. My name is Matthias, I am from Germany and am so old that I have seen the original of "ANH" in the age of ten years in the cinema.

    Now, 39 years...
Results 1 to 12 of 12