Search:

Type: Posts; User: Forgetful Jedi Knight

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. It should work, you just have to check the length.

    It should work, you just have to check the length.
  2. Replies
    3
    Views
    121

    The TCSS Black Friday Sale is live now with 20%...

    The TCSS Black Friday Sale is live now with 20% Off Sitewide! Some exclusions do apply. Orders will not begin to process until Monday 11/29 and the sale is only valid Today and Tomorrow (25th and...
  3. Replies
    1
    Views
    92

    Correct.

    Correct.
  4. You mean these? ...

    You mean these?

    https://www.thecustomsabershop.com/Heatsink-module-for-1-ID-tubes-with-center-hole-P1011.aspx
  5. Since I donít really use anything other than PL...

    Since I donít really use anything other than PL boards, I donít know exactly what a GH board can do, but I am aware that the GH is suppose to be a fairly simple board.

    And CFX can handle matching...
  6. Ummm, the CFX and GHv3 boards are two seperate...

    Ummm, the CFX and GHv3 boards are two seperate boards.
  7. Pictures would be a huge help here.

    Pictures would be a huge help here.
  8. Replies
    10
    Views
    864

    Try not to make a habit of it, I canít get always...

    Try not to make a habit of it, I canít get always get Erví to respond right away. 😉
  9. Replies
    10
    Views
    864

    Good news, if itís just the one little blob you...

    Good news, if itís just the one little blob you showed me, the Top says youíll be fine.
  10. Replies
    10
    Views
    864

    Ok, that doesn’t look TOO Bad. The easiest way to...

    Ok, that doesn’t look TOO Bad. The easiest way to deal with that is to take your soldering iron, hopefully, it’s a nice fine tip, make sure it is completely clean and hot and try to “divide” that...
  11. Replies
    10
    Views
    864

    Worst comes to worst, Iíll have Chewbacca get in...

    Worst comes to worst, Iíll have Chewbacca get in touch if it needs fixing.
  12. Replies
    10
    Views
    864

    LOL. “A friend”, huh? I forwarded this to the...

    LOL. “A friend”, huh? I forwarded this to the top. I think I know the answer to that, but I’ll let him chime in to verify before I say anything. I’ll let you know when I hear back or maybe you’ll...
  13. Replies
    4
    Views
    590

    Both power lines (+) and (-) should be at least...

    Both power lines (+) and (-) should be at least 22 gauge.
  14. Replies
    4
    Views
    590

    Yes, that will work fine.

    Yes, that will work fine.
  15. The links are invalid.

    The links are invalid.
  16. Ok, a few things. You should be able to run...

    Ok, a few things.

    You should be able to run both LEDs off of the two switches and the one battery, though if you have room for a 7.4V pack, I donít understand why you wouldnít have room for 2...
  17. No, they tend to be unprotected.

    No, they tend to be unprotected.
  18. If youíre using a pixel blade, you need a 15A...

    If youíre using a pixel blade, you need a 15A drain battery.
  19. Thatís usually a configuration issue.

    Thatís usually a configuration issue.
  20. Replies
    4
    Views
    866

    There are several reasons, but Iím not going to...

    There are several reasons, but Iím not going to get into them.
  21. Replies
    4
    Views
    866

    Welcome to the Forums. That company isnít...

    Welcome to the Forums.

    That company isnít usually mentioned in these parts. Electronics can be put into the saber, but youíd likely have to send it out, unless you have experience installing...
  22. Generally, no they don’t. With those, the...

    Generally, no they don’t. With those, the polarity matters.
  23. You would be correct. Yeah, that was a discussion...

    You would be correct. Yeah, that was a discussion today, as well as prototyping other stuff.
  24. Funny you should ask about that… ...

    Funny you should ask about that…

    https://i.ibb.co/YdRpfMd/F945-E074-C5-B4-436-C-9-AEB-2-EF3437-A036-D.jpg

    For the most part, it is a tight fit, and in some spots, a VERY tight fit.
  25. For the most part, youíre on the right track....

    For the most part, youíre on the right track. Regarding the switches, you may be able to use the latching switch as the activation switch with a CFX (youíd have to check the manual), but I think they...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4