Search:

Type: Posts; User: jjshumpert

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    22
    Views
    8,876

    if you have issues later an hour in the freezer...

    if you have issues later an hour in the freezer helps as well
  2. Replies
    22
    Views
    8,876

    im well over 20 grand, with over 3 grand in my...

    im well over 20 grand, with over 3 grand in my personal hilts
  3. Replies
    88
    Views
    33,367

    nova i have had the 2010 boards run on single...

    nova i have had the 2010 boards run on single 18650's, 2x18650's, 4.8 nihm AAA packs, and the 6v AA holder running 2500mah nihm cells. i havent metered the board outputs, but i cant tell much...
  4. Replies
    22
    Views
    10,749

    i love the look of this one fb, great design and...

    i love the look of this one fb, great design and you really pulled off the hard used look, im really impressed with this one buddy!
  5. Replies
    11
    Views
    4,882

    well like i said, i have an mr board running a p4...

    well like i said, i have an mr board running a p4 red, in fact im holding onto it as im typing this, and with it running it is warm, but the bh and heat sink takes care of that just fine. and i have...
  6. Replies
    11
    Views
    4,882

    yeah they all do that buddy, thats what the heat...

    yeah they all do that buddy, thats what the heat sink is for :D
  7. Replies
    14
    Views
    7,147

    if it is the thicker body, just sand the inside...

    if it is the thicker body, just sand the inside of the hilt until the blade holder slides into place. when mr was putting these hilts out we had the same trouble, although the hilts had the removable...
  8. Replies
    11
    Views
    4,882

    i have a vader on the bench that has been running...

    i have a vader on the bench that has been running a p4 red for over a year with no issue
  9. Replies
    14
    Views
    7,147

    the only differences found in the ani hilts are...

    the only differences found in the ani hilts are some where of a thicker hilt body material that needs to be sanded to allow the conversion to fit. tims kit works for the hasbro anakins no problem
  10. Replies
    11
    Views
    4,882

    no need for resistors with mr boards, think of it...

    no need for resistors with mr boards, think of it as a buckpuck with sound
  11. Replies
    11
    Views
    4,898

    18650 is roughly twice the size of AA

    18650 is roughly twice the size of AA
  12. Replies
    11
    Views
    4,898

    with a little chasis rework 4 1000mah AAA's will...

    with a little chasis rework 4 1000mah AAA's will fit in place of your 18650 no problem
  13. Replies
    32
    Views
    83,798

    dont get one of the grand rapids international...

    dont get one of the grand rapids international products ones in the orange casing, they die in a matter of months
  14. Replies
    32
    Views
    83,798

    i cut the saber emitter on either side, pretty...

    i cut the saber emitter on either side, pretty much no other way to get the saber apart otherwise. you can still put it back together and play with it.
  15. Thread: MHS coupler

    by jjshumpert
    Replies
    128
    Views
    63,960

    good deal, any idea when this might make it to...

    good deal, any idea when this might make it to the store? i need 3 sets :D
  16. Replies
    15
    Views
    10,476

    the endors dont work because the dies are towards...

    the endors dont work because the dies are towards the outside of the star, but there are triple die stars that the emitters are close to the center of the star that are usable. there are optics for...
  17. Thread: MHS coupler

    by jjshumpert
    Replies
    128
    Views
    63,960

    heres a question for ya tim, in use of these...

    heres a question for ya tim, in use of these couplers with sound saber do you think we will have to use a reverse sound setup? im just looking at the design and it doesnt seem like sound ports in...
  18. Replies
    3
    Views
    2,471

    if you look closely at the board all the required...

    if you look closely at the board all the required connections are labeled beside the pads
  19. Replies
    38
    Views
    15,710

    no worry of the self etch damaging your hilt, i...

    no worry of the self etch damaging your hilt, i use it all the time when painting cars. basically what it does it eats away any impurities on the surface of the metal. just make sure you use it...
  20. i bend back the connection to the board negatives...

    i bend back the connection to the board negatives and solder it directly to the board
  21. Replies
    8
    Views
    5,379

    ive heard of the 2010 boards having different...

    ive heard of the 2010 boards having different fonts, but i havent had much experience with this as i only use the vader boards
  22. Replies
    8
    Views
    5,379

    looks good, which econ board will you be using in...

    looks good, which econ board will you be using in this hilt?
  23. Replies
    9
    Views
    5,706

    another great saber! and i was really impressed...

    another great saber! and i was really impressed with your connections between the sound/crystal chamber module and your lux module, a simple and well conceived system. this time im going to have to...
  24. Replies
    15
    Views
    6,169

    yup your led + should come off the vdd that your...

    yup your led + should come off the vdd that your clash is hooked up to
  25. Replies
    15
    Views
    6,169

    not if you charged em yesterday... mind uploading...

    not if you charged em yesterday... mind uploading a pic of your wiring diagram?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4