Search:

Type: Posts; User: Uncle67

Search: Search took 0.00 seconds.

  1. Thread: New hilts?

    by Uncle67
    Replies
    1
    Views
    10,305

    New hilts?

    Is there a time frame for the new hilts?

    I am also looking for a good Kanan hilt. A kit. Not one that has been built. A Maul and Ahsoka as well.
  2. Thread: Sound issue

    by Uncle67
    Replies
    19
    Views
    24,955

    I purchased a universal charger. Once it was...

    I purchased a universal charger. Once it was fully charged, the sound issue is no longer there.
  3. Thread: Sound issue

    by Uncle67
    Replies
    19
    Views
    24,955

    My friend has the same charger. He said that his...

    My friend has the same charger. He said that his LED light comes on when he plugs it in the wall. Mine does nothing. My cheap $5 voltmeter shows no current. I am going to take my electronics to him...
  4. Thread: Sound issue

    by Uncle67
    Replies
    19
    Views
    24,955

    This is how I have it hooked up at this time....

    This is how I have it hooked up at this time. Anyone see anything off?

    Nano Biscotte v4 install with Tri-Cree and recharge port build
    Parts:
    1. NBv4
    2. Tri-Cree (deep red, deep red and blue for...
  5. Thread: Sound issue

    by Uncle67
    Replies
    19
    Views
    24,955

    Unfortunately my volt meter is limited. It is...

    Unfortunately my volt meter is limited. It is mainly for small batteries. It was super cheap. I need a better one. However, I can set it on everything and get nothing. I get resistance only. No...
  6. Thread: Sound issue

    by Uncle67
    Replies
    19
    Views
    24,955

    I have taken it apart about three times. I just...

    I have taken it apart about three times. I just noticed that the charger may not be working. Tim has been helping me figure this out. He is a patient man.
  7. Thread: Sound issue

    by Uncle67
    Replies
    19
    Views
    24,955

    I will be taking it apart and re doing the wires....

    I will be taking it apart and re doing the wires. Now, it will not come on. I did charge the battery yesterday with no change. I am wondering if something is wrong with the board.
  8. Replies
    3
    Views
    3,252

    I have seen that section. That is why I had...

    I have seen that section. That is why I had questions. I just haven't seen any done yet.
  9. Thread: Sound issue

    by Uncle67
    Replies
    19
    Views
    24,955

    https://youtu.be/ZmyLB8K3hro

    https://youtu.be/ZmyLB8K3hro
  10. Thread: Sound issue

    by Uncle67
    Replies
    19
    Views
    24,955

    I got everything from CSS. I will dig further. ...

    I got everything from CSS. I will dig further.
    The chassis with the kill switch is very tight in the hilt. I will check some wiring and order new resistors for the red.
  11. Thread: Sound issue

    by Uncle67
    Replies
    19
    Views
    24,955

    It did not work. After it is on, the sound starts...

    It did not work. After it is on, the sound starts again. If I shut it off and turn it back on, it is there. I am leaning towards a resistor issue since my resistors for my red get hot. I do have a...
  12. Replies
    3
    Views
    3,252

    Maglite conversion

    Has anyone done a Maglite into a saber conversion? I have a few of them laying around. I have a 5 D cell sitting in a closet.
  13. Thread: Sound issue

    by Uncle67
    Replies
    19
    Views
    24,955

    :) :) Thank you! :)

    :)

    :) Thank you! :)
  14. Thread: Sound issue

    by Uncle67
    Replies
    19
    Views
    24,955

    Sounds good. I will give it a shot tonight. Thank...

    Sounds good. I will give it a shot tonight. Thank you!
  15. Thread: Sound issue

    by Uncle67
    Replies
    19
    Views
    24,955

    Sound issue

    I have had the saber working for a few days. Today, after a minute of it running, it makes a loud static sound. Not like a loose wire sound, but an issue maybe coming from the board. Could this be an...
  16. Replies
    7
    Views
    4,504

    Thanks. I did finish it. Now I am going to...

    Thanks. I did finish it. Now I am going to re-doit. The switch is a pain. I found a screw that was stripped. I also do not like how the retention screw is for looks and the actual retention is by...
  17. Replies
    7
    Views
    4,504

    I like your video! Resistors. I have deep red...

    I like your video!

    Resistors. I have deep red for two main and blue for the flash on clash. I currently have two 2 ohm/1 watt for my red and have a 0.5 ohm/3 watt for my blue. This was directed to...
  18. Replies
    7
    Views
    4,504

    I just realized that I renamed the volt meter. I...

    I just realized that I renamed the volt meter. I am currently a little medicated because of flu symptoms. I was trying to say I was testing using the ohm setting. ;)
    Your information is awesome....
  19. Replies
    7
    Views
    4,504

    MPP 2.0 AV switch

    This is my first build. I am building an ESB Darth Vader saber using the Tri-Cree and an NBv4. I may get some help locally, but I am trying to do this as much as possible before I do.
    The switch...
Results 1 to 19 of 19