Search:

Type: Posts; User: Oleenick

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    11,712

    Sorry to take up anyone's time, turns out, after...

    Sorry to take up anyone's time, turns out, after soldering and re-soldering some connections, all was fine. Not sure how those connection impacted the motion sensing ability... Loving the NBV4
  2. Replies
    2
    Views
    11,712

    NBV4 Motion Sense suddenly not working

    Hello TCSS Forum!

    Today I was finishing off my build with the NBV4 and, after I had soldered everything up and fit it in a neat chassis, no motion sense.

    I am nervous that I may have somehow...
  3. Replies
    0
    Views
    9,531

    Buying my first build!

    Hello all!

    After much revision from the advise of Tom and Seth, I'm here: http://www.thecustomsabershop.com/ViewWishlist.aspx?ViewCode=99335742-d5ac-4314-ad40-6f4b653936d7

    I live in Australia,...
  4. Replies
    11
    Views
    19,791

    Thanks! I didn't realise that these were...

    Thanks! I didn't realise that these were trustworthy specs as I thought there was strong variance but if this is what everyone uses, so will I.
  5. Replies
    11
    Views
    19,791

    Bump, Yeah I'll go for the deep red. Do you know...

    Bump, Yeah I'll go for the deep red. Do you know what resistor is best for that?

    Thanks!
  6. Replies
    11
    Views
    19,791

    I was originally thinking red but deep red seems...

    I was originally thinking red but deep red seems better I think.
  7. Replies
    11
    Views
    19,791

    Do you know what Ohm resistor I would need for...

    Do you know what Ohm resistor I would need for the red LED?
  8. Replies
    11
    Views
    19,791

    Thanks! I've added what you've suggested to the...

    Thanks! I've added what you've suggested to the wishlist.

    I do have my own stockpile of wires to use. The LED is RGB

    What do you mean by harness the LED? I could be wrong but what I have seen...
  9. Replies
    11
    Views
    19,791

    My first build!

    Hello TCSS Forum!

    Looks like its time for me to make my first build!

    This is my part list: http://www.thecustomsabershop.com/ViewWishlist.aspx?ViewCode=99335742-d5ac-4314-ad40-6f4b653936d7
    ...
  10. Replies
    2
    Views
    15,034

    Thanks for the reply! I think I'll get a 1"...

    Thanks for the reply!

    I think I'll get a 1" blade with a trans white finish, and then maybe use some cellophane if I think its not good enough.

    I'd love to get a 1" heat sink but the Heat Sink...
  11. Replies
    2
    Views
    15,034

    Differences in blades.

    Hello TCSS Forums!

    I'm doing a 3D printed hilt lightsaber and have a few questions relating to that.

    I am currently trying to decide on a blade, this is my current wishlist:...
  12. Replies
    4
    Views
    5,253

    Thanks for the replies, that's clarified a lot. ...

    Thanks for the replies, that's clarified a lot.

    Would you by chance know the forward voltage of the Tri-Rebel? I was considering testing it once it arrived but I just wanted a first hand account....
  13. Replies
    4
    Views
    5,253

    Electronics Check

    Hello TCSS Community!

    I'm relatively new here, with some electronics knowledge. I'd like to run the electronics I might be using past all you savvy people.

    Here's my list so far:
    ...
Results 1 to 13 of 13