Search:

Type: Posts; User: UltraSWG

Page 1 of 11 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    19
    Views
    7,509

    I wouldn't wait too long. I'm running low on...

    I wouldn't wait too long. I'm running low on boards already, so I'd guess that Tim isn't sitting on a large quantity either since he sells alot more components to DIY folks than I do.

    And I don't...
  2. Thread: sound with el

    by UltraSWG
    Replies
    27
    Views
    51,053

    I know this thread is old, but I think I need to...

    I know this thread is old, but I think I need to point out that it doesnt matter how well you secure the blade or set screw. There will always be a risk of LED exposure from the blade tip coming off....
  3. Replies
    16
    Views
    8,224

    The power management on the board has not...

    The power management on the board has not fundementally changed. Its been tweaked to be more efficient, but Jay Gon is correct.
  4. Replies
    465
    Views
    136,840

    Sounds like a ghost in the machine!

    Sounds like a ghost in the machine!
  5. Replies
    465
    Views
    136,840

    Everything worked fine out of the hilt, but then...

    Everything worked fine out of the hilt, but then stopped working once you put it in the hilt?
  6. Replies
    9
    Views
    3,230

    Ideally it's best to run the pot *before* the...

    Ideally it's best to run the pot *before* the amp, but since that's not possible, a higher ohm pot after the amp will also work.
  7. Replies
    9
    Views
    3,230

    Using a potentiometer for volume control is a...

    Using a potentiometer for volume control is a simple enough matter. Just run a 500K ohm pot inline with the speaker.
  8. Replies
    465
    Views
    136,840

    Made another vid with the radio shack switch...

    Made another vid with the radio shack switch mentioned in this thread. Also demonstrating the max sensitivity settings:

    http://www.youtube.com/watch?v=V8BOA0_FfGY
  9. Replies
    465
    Views
    136,840

    Tactile switches are low bounce by their very...

    Tactile switches are low bounce by their very nature; they are membrane activated, rather than plunger. Tactiles are easy to work with, too, you can even gut your favorite plunger type of switch and...
  10. Replies
    465
    Views
    136,840

    Not sure, don't have a ribbed section to test. ...

    Not sure, don't have a ribbed section to test. Will a ribbed section fit a side by side AA pack?

    BTW, yall, having to have the board mounted IS NOT an issue *if* you are using a good switch. We...
  11. Replies
    465
    Views
    136,840

    I made a vid of the compact setup: ...

    I made a vid of the compact setup:

    http://www.youtube.com/watch?v=yWyUcBfXO_o
  12. Replies
    465
    Views
    136,840

    Hey Duck, if it was loud outside the saber, but...

    Hey Duck, if it was loud outside the saber, but became muffled when you put it in the hilt, you'll need to redesign the acoustics of the hilt itself. Make sure you have a good resonance chamber and...
  13. Replies
    465
    Views
    136,840

    ArmOnFire, and Kal, did yall even watch the...

    ArmOnFire, and Kal, did yall even watch the video? There is no change in power requirements.

    There is nothing wrong with the board, it isn't failing. You just have to deliver power to it...
  14. Replies
    465
    Views
    136,840

    That would explain it.

    That would explain it.
  15. Replies
    465
    Views
    136,840

    Can you try some new batteries and see if the...

    Can you try some new batteries and see if the problem persists? Thanks.
  16. Replies
    465
    Views
    136,840

    This may sound stupid, but how long have you been...

    This may sound stupid, but how long have you been using the same set of batteries? You said you were running a K2, and AAA's are only good for maybe half an hour of life when running a K2. 1500mah...
  17. Replies
    465
    Views
    136,840

    It's not a holder issue. Any holder will work. I...

    It's not a holder issue. Any holder will work. I built an UltraSound 2.0 powered Obi Wan FX for Seth using a side by side AA holder.
  18. Replies
    465
    Views
    136,840

    Not yet, bu if Rayovacs work, I don't see why...

    Not yet, bu if Rayovacs work, I don't see why Duracells would not.
  19. Replies
    465
    Views
    136,840

    Spontaneous turn on, eh? I'll keep an eye out...

    Spontaneous turn on, eh? I'll keep an eye out for that one. I usually take the batteries out of my Graflex if it's going to sit for that long since the board still draws power when asleep.

    As...
  20. Replies
    465
    Views
    136,840

    Well welcome to TCSS, Hullbreach. Strydur is the...

    Well welcome to TCSS, Hullbreach. Strydur is the gold standard for customer service, man, rest assured.
  21. Replies
    465
    Views
    136,840

    Video is live ...

    Video is live

    http://www.youtube.com/user/UltraSWG
  22. Replies
    465
    Views
    136,840

    As my video will show, there really aren't any...

    As my video will show, there really aren't any problems at all with the board. Youtube is taking a LONG time to process my video.

    And hullbreach, my return policy is the same as it's always been,...
  23. Replies
    465
    Views
    136,840

    Yup, it will be on my channel, I'm uploading now.

    Yup, it will be on my channel, I'm uploading now.
  24. Replies
    465
    Views
    136,840

    It has nothing to do with the batts and holders,...

    It has nothing to do with the batts and holders, really, any batts and holders will work, you don't need Li-Ions or even Lithium primaries. I figured it out, it was really quite simple. The video...
  25. Replies
    465
    Views
    136,840

    Ok, I did some experiments on 4.5, 6, and 7.2...

    Ok, I did some experiments on 4.5, 6, and 7.2 volts. The results are like I figured, the board actually works like it's supposed to, even on 4.5 volts, you just need consistent power when first...
Results 1 to 25 of 273
Page 1 of 11 1 2 3 4