Search:

Type: Posts; User: CreativeForce

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    573

    Is there an LED in your switch? If so, what...

    Is there an LED in your switch? If so, what color? If not, then you shouldn't need a resistor.
  2. Replies
    2
    Views
    470

    Thanks FJK! I'll still be able to access the SD...

    Thanks FJK! I'll still be able to access the SD card as I'm just rotating the sound board 180. I'm going to play around with it a little to see if I can figure out a way to place the card right side...
  3. Replies
    2
    Views
    470

    NBIV orientation in hilt

    Hello All, I'm currently working on my fourth install and was wondering if the orientation of the NBIV matters? More specifically, I've done my previous installs with the contacts towards the emitter...
  4. Thanks Tom! Once again I see you as a master and...

    Thanks Tom! Once again I see you as a master and I, but a padawan.
  5. 1" Thick wall diffuser in 7/8" thin wall blade?

    Hi All, I seem to remember seeing or reading somewhere that the blade diffuser for the 1" Thick wall blades will also fit the 7/8" thin wall blades. Does anyone know if this is true?
  6. Replies
    8
    Views
    1,337

    So, since I am using the Panasonic 3.7 li-ion 10...

    So, since I am using the Panasonic 3.7 li-ion 10 amp from TCSS, and I plan to run two wires from each the positive and negative of the hilt side neo-pixel PCB, I should be okay with 26 gauge wire as...
  7. Replies
    8
    Views
    1,337

    Thanks Tim! So would you be splitting the current...

    Thanks Tim! So would you be splitting the current if you have the two leads coming off the Neo-pixel PCB? Two each for neg and pos?
  8. Replies
    8
    Views
    1,337

    Wire Gauge for Neo Pixel

    Hello All,
    I'm currently building a Neo Pixel with 26 gauge wire, but I'm seeing some folks post about using 24 gauge wire for their Neo Pixel builds. Am I okay with the 26?
    And looking ahead, my...
  9. I'm re-thinking now if I should put the resistor...

    I'm re-thinking now if I should put the resistor in the blade as that does indeed seem to be the way that most people are building blades. And the shop getting the new SMD resistors in stock doesn't...
  10. Replies
    1
    Views
    433

    Pictures would help. First thing is to check you...

    Pictures would help.
    First thing is to check you have a full charge on your battery. Next is just to go through each wire joint and carefully inspect your solder joints to make sure you have no...
  11. 7/8" Neo Pixel hilt adaptor on Graflex 2.5

    I've recently gotten a Graflex 2.5 kit and have decided to go the neo pixel route with it. I'm trying to get my shopping list in order and my question would be how to secure the Neo Pixel adaptor in...
  12. Replies
    4
    Views
    1,293

    Nice! Thanks Tim!

    Nice! Thanks Tim!
  13. Replies
    4
    Views
    1,293

    Got it. thanks Tom!

    Got it. thanks Tom!
  14. Replies
    4
    Views
    1,293

    Drilling out Blade Tips?

    Hi Everyone,
    I'm building my fist Neo-Pixel and the blade to go with it. I've seen some posts about people drilling out the tip of the blade. (I imagine to get rid of the mirror finish and let light...
  15. Thanks Tom! Here's a link to a higher res...

    Thanks Tom!
    Here's a link to a higher res diagram.

    https://imgur.com/a/WYDtiIu

    All the builds I've done so far have been traditional in hilt tri-Cree's, and I was really happy with...
  16. Time to take the plunge! First Neopixel build.

    Hello Saber Makers! It's time for me to take the plunge and try my hand at Neo pixel. The effects they offer are just too great to pass up. Here is my preliminary wiring diagram. Any and all comments...
  17. Figured it out! And done! 1691216913 Here's a...

    Figured it out! And done!
    1691216913

    Here's a link to more.
    https://imgur.com/a/v48OLPp
  18. So it's been a while but I'm actually very close...

    So it's been a while but I'm actually very close to completing this. I was starting to wire up the PeX and I began to have second thoughts. As you can see from my wiring diagram, I had it drawn out...
  19. Replies
    2
    Views
    711

    MHS parts CAD symbols?

    Hi everyone! Does anyone know where to find(or does anyone have) the MHS V1 parts as CAD symbols? I did a search but didn't find anything. The builder is great for 2D views, but I'd love to import my...
  20. Ah, thanks for turning on the lightbulb for me!...

    Ah, thanks for turning on the lightbulb for me! So reading through the manual it sounds like the deep sleep pad would be the most effective for me (especially if I forget/lose the kill key) That's a...
  21. That's how I did my first build which was a tri...

    That's how I did my first build which was a tri R,R,rB star, since I knew the red would be on all the time.
    With an R,G,B star (And please correct me here if my reasoning is incorrect) if I were to...
  22. Is there a better way? Ideally I would want it to...

    Is there a better way? Ideally I would want it to come on with the activation switch, but I wasn't sure if I could wire up the negative of the LED in the switch to the ACT on the NBIV? Or would it be...
  23. LOL, I Haven't built it yet.This is only step one...

    LOL, I Haven't built it yet.This is only step one - drawing it out, and planning the chassis build. Last one worked out great so I'm getting a little more ambitious this time around. I'll be using a...
  24. Replies
    2
    Views
    682

    Awesome, thanks!

    Awesome, thanks!
  25. Replies
    2
    Views
    682

    NBIV Default Sound Banks

    Does anyone know if the default sound banks on the NBIV are in this order:
    Bank 1 = Lightmeat
    Bank 2 = Greymeat
    Bank 3 = Darkmeat

    I want to change the boot up sounds on each so I can more...
Results 1 to 25 of 41
Page 1 of 2 1 2