Search:

Type: Posts; User: Tom Tilmon

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Absolutely killer saber and inspiration! Awesome...

    Absolutely killer saber and inspiration! Awesome work E57!!!!!!
  2. Replies
    14
    Views
    596

    Seth this is awesome. Love it as always!!!!!

    Seth this is awesome. Love it as always!!!!!
  3. Replies
    1
    Views
    195

    3.7 volts. 12 is probably a maximum rating...

    3.7 volts. 12 is probably a maximum rating stamped on there. Figure your resistor for your supply.
  4. Eeek, I haven't logged into SLD in a bit. I've...

    Eeek, I haven't logged into SLD in a bit. I've been too busy building sabers.
  5. Blackcowl, it wasn't clear you were using a prism...

    Blackcowl, it wasn't clear you were using a prism until later on. I have modified the bulb release area for 2 switches in there, and it worked. I then use the old slide switch in the clamp as a...
  6. I have begun my 3 builds. I'm building 3 of...

    I have begun my 3 builds. I'm building 3 of these, and after honing out one of my quillions today.....2.5 hours later, I don't think I'll take on one of these crossguards again. The 3/4 ID on the...
  7. Replies
    14
    Views
    596

    I like it, just not as much as the Jedi Killer. ...

    I like it, just not as much as the Jedi Killer. Awesome work again Seth!!!!!
  8. Replies
    7
    Views
    777

    The momentary button has a switch wire, and then...

    The momentary button has a switch wire, and then a ground. It looks like your ground is going to negative with the battery negative. I can't see the wiring where you come out of the GND side of...
  9. Replies
    1
    Views
    277

    Awesome work Anvil. Boring out the K4, I bet...

    Awesome work Anvil. Boring out the K4, I bet that was a gut wrenching moment.
  10. Replies
    18
    Views
    2,303

    If you are using an improper battery, this is...

    If you are using an improper battery, this is common because of the high drain neopixels can put on the battery, it may cause the amp to drop out due to lack of power. You must use a battery with...
  11. Glad you got them, hope you are making progress!

    Glad you got them, hope you are making progress!
  12. Hope they get to you soon. I've been thinking...

    Hope they get to you soon. I've been thinking about this, not sure how dual switches will work in the clamp. There needs to be fulcrum between the two so only one activates at a time. Then you...
  13. Replies
    9
    Views
    621

    Of course then there is always: Deep Red, Green,...

    Of course then there is always: Deep Red, Green, Royal Blue dR, G, rB ! You can really get some crazy purples with deep red and royal blue.
  14. https://i.imgur.com/KLJ6x8l.jpg

    https://i.imgur.com/KLJ6x8l.jpg
  15. I don't work for TCSS, I'm just a schmo like you....

    I don't work for TCSS, I'm just a schmo like you. I'll drop those switches in an envelope to you. As for blades, for in-hilt builds, I like clear blades with clear cellophane wraps inside. There...
  16. My answers to your questions are in red. I hope...

    My answers to your questions are in red. I hope this helps.
  17. sounds familiar, on the aux button jewel fiasco. ...

    sounds familiar, on the aux button jewel fiasco. Been there, done that.
  18. Replies
    7
    Views
    850

    Awesome K6!

    Awesome K6!
  19. Thread: Videos

    by Tom Tilmon
    Replies
    49
    Views
    51,320

    Sticky: Absolutely insane design! Awesomely creative. ...

    Absolutely insane design! Awesomely creative. How fragile is the clay once it hardens? Where did you get it?

    TOm
  20. You can find it at almost any hardware store. I...

    You can find it at almost any hardware store. I don't use it very often, but there are some things that it works well on, and this might be one of those rare instances.

    Tom
  21. E6000 or Liquid Electrical Tape? That might...

    E6000 or Liquid Electrical Tape? That might work. Your shrink should be sufficient. If the contacts are exposed through the chassis, just put a bit of liquid electrical tape over them.

    Tom
  22. Replies
    4
    Views
    605

    Painted, powdercoated,or real copper? Looks...

    Painted, powdercoated,or real copper? Looks great.
  23. Replies
    10
    Views
    791

    glad you got it worked out!

    glad you got it worked out!
  24. If you're running single wires off your...

    If you're running single wires off your neopixels, then yes, 22 ga PTFE will work. You can use thinner wire 30 or 32 for switches/data. I was able to fit my 2 strands of 22 into the knight wire...
  25. Another basic video worth watching: Another...

    Another basic video worth watching:

    Another video worth watching, where Madcow uses this chassis, and shows how to use the T8 tubing:
    https://www.youtube.com/watch?v=sApB7J5JdZ4[/VIDEO]
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4