Search:

Type: Posts; User: TheMohawkNinja

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    12,966

    So, I don't have a "standard" momentary switch on...

    So, I don't have a "standard" momentary switch on hand, so I just disconnected the switch. I then directly bridged the accent pad to the black wire that is tied into the white wire that goes from the...
  2. Replies
    7
    Views
    12,966

    It's not supposed to be pretty, as it's just...

    It's not supposed to be pretty, as it's just making sure that I actually know what I'm doing.

    I'm not sure what you mean by activation negative. If you mean the common pin of the switch, that's...
  3. Replies
    7
    Views
    12,966

    Yes. I did, there's an Imgur link in the OP.

    Yes.


    I did, there's an Imgur link in the OP.
  4. Replies
    7
    Views
    12,966

    Nano Bisc. V4 activation issues

    Hello,

    I recently soldered up a Nano Bisc V4 to make sure everything is wired correctly. On the first power on, everything worked fine (power up sound when removing kill key, and LED+sound when...
  5. Replies
    19
    Views
    16,068

    So, have you talked to this "Zook" person yet by...

    So, have you talked to this "Zook" person yet by chance? I have yet to get a PM or anything.
  6. Replies
    19
    Views
    16,068

    Awesome, I wouldn't of even thought that would...

    Awesome, I wouldn't of even thought that would have been economically feasible.
  7. Replies
    19
    Views
    16,068

    I don't know how, but upon closer inspection, I...

    I don't know how, but upon closer inspection, I have in-fact wired the board in reverse.

    I have now corrected the issue, and upon pressing the activation switch, I get no sound, the switch LED...
  8. Replies
    19
    Views
    16,068

    Yes, each other. I powered on the board and had...

    Yes, each other. I powered on the board and had those wires touch each other when they were only soldered on the board pads and nothing else. Touching the wires together did not appear to affect the...
  9. Replies
    19
    Views
    16,068

    What do you mean by a "real momentary switch"? I...

    What do you mean by a "real momentary switch"? I thought a momentary switch is defined as a switch which (if in normally open state) will close only while the switch is held down, or (if in normally...
  10. Replies
    19
    Views
    16,068

    https://imgur.com/a/wQRk3zO I would like to...

    https://imgur.com/a/wQRk3zO

    I would like to note that (A) I have a known latching switch from the same manufacturer, and it clearly functions mechanically differently (the known latching switch...
  11. Replies
    19
    Views
    16,068

    It is a momentary switch.

    It is a momentary switch.
  12. Replies
    19
    Views
    16,068

    Here's a few to start out with:...

    Here's a few to start out with: https://imgur.com/a/ueOYKBJ

    Let me know if there are any other pics you want.

    Thank you,
  13. Replies
    19
    Views
    16,068

    Right, but I've already confirmed that no bridge...

    Right, but I've already confirmed that no bridge exists on the pads, and I haven't added solder to any other part of the board, so I am unsure of what traces and/or chip pins need tested to determine...
  14. Replies
    19
    Views
    16,068

    Potentially fried board. How to confirm?

    Hello,

    So, the wiring layout, issue, and troubleshooting steps that have been taken can be found on a Reddit thread here:...
  15. I chose the eBay one, because it is a "proud"...

    I chose the eBay one, because it is a "proud" switch (that is, the button is above the outer ring) which makes it a lot easier to use IMO. I can do some more research and see if I can't find a...
  16. So, would this be more correct as far as the...

    So, would this be more correct as far as the negative wiring and resistances is concerned?
    https://preview.ibb.co/b6nhPU/Wiring_diagram.png

    As for the use of a momentary switch, why does the type...
  17. Awesome, okay that makes perfect sense. Does the...

    Awesome, okay that makes perfect sense. Does the rest of the layout I have seem good?
  18. First time setup. Want to make sure everything is good before soldering.

    Hello,

    Finally got all the parts to start soldering, but I would like someone to double-check by (definitely not technical, but I'm learning how to fix that) wiring diagram.

    The switch is from...
Results 1 to 18 of 18