Search:

Type: Posts; User: jbkuma

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    121

    You can buy clear pvc, you'll probably want to...

    You can buy clear pvc, you'll probably want to search for "architectural pvc" the main advantage over polycarbonate and acrylic is that it is less likely to break and easier to work with because it...
  2. Soldering through makes it easier to solder to...

    Soldering through makes it easier to solder to both sides since the wire is less likely to ping off, although one side would usually be surface.
  3. if you only have to make small adjustments use...

    if you only have to make small adjustments use small files, you'll have more control and less likely for things to go horribly wrong.
  4. Replies
    5
    Views
    349

    Your 7.4 battery is destroying the pixels, you...

    Your 7.4 battery is destroying the pixels, you need a single cell.
  5. Replies
    4
    Views
    318

    soon enough your burners go 8 deep and 12 wide.

    soon enough your burners go 8 deep and 12 wide.
  6. Replies
    3
    Views
    404

    Even if the rated forward voltages are accurate,...

    Even if the rated forward voltages are accurate, the green will operate at around 2A at 4+v. While communal experience will say that it will survive, it's still not ideal. The old "wisdom" that the...
  7. Replies
    3
    Views
    404

    I think a lot of people like to psych people out...

    I think a lot of people like to psych people out of the crystal chamber, but I don't see why. I'm sure you can do it.

    As far as I can tell the diagram looks fine. You should have resistors on...
  8. Replies
    13
    Views
    815

    I always feel like I should be documenting how I...

    I always feel like I should be documenting how I do things for some reason, which is one of the reasons I don't post as many of my creations as I should. The organic process of making things is what...
  9. Replies
    8
    Views
    721

    Very nice, I love seeing sabers take inspiration...

    Very nice, I love seeing sabers take inspiration from unique sources!
  10. Replies
    7
    Views
    568

    if you put a half inch piece of PVC inside it is...

    if you put a half inch piece of PVC inside it is almost the same OD as the blade's ID and use a pipe cutter. It will be clean and have a nice rounded edge. No dust to worry about....
  11. Replies
    1
    Views
    646

    Yes. You don't have to do anything, but that is...

    Yes. You don't have to do anything, but that is recommended for a reason. I personally use 20awg. This has nothing to do with the CFX, it's physics.
  12. Replies
    57
    Views
    10,775

    Sticky: Ah well, sadly I've been waiting on parts to...

    Ah well, sadly I've been waiting on parts to arrive for a couple of months :(

    I'm looking forward to seeing what everyone submitted!
  13. Replies
    6
    Views
    678

    Regardles of the board, you are going to want to...

    Regardles of the board, you are going to want to shorten up those bare ends. As minimal as possible to make good contact. You most assuredly have or will have intermittent or terminal shorts with...
  14. Replies
    2
    Views
    550

    Very nice! I especially appreciate that pommel.

    Very nice! I especially appreciate that pommel.
  15. Replies
    15
    Views
    1,851

    what did you use to wire it up?

    what did you use to wire it up?
  16. Replies
    6
    Views
    729

    Entropy!

    Entropy!
  17. Replies
    9
    Views
    1,600

    You are better off running your blade at around...

    You are better off running your blade at around 80-90% brightness from the start. It will reduce the drain and improve the battery life significantly, and the brightness won't be affected that much...
  18. Replies
    9
    Views
    1,600

    Unless you are using a matched pair of batteries...

    Unless you are using a matched pair of batteries or a battery pack it is not a good plan to wire lithium cells in parallel.
  19. Thread: Ianthe build

    by jbkuma
    Replies
    9
    Views
    1,380

    you can think of it kind of like ripping a DVD...

    you can think of it kind of like ripping a DVD and posting it to YouTube.
  20. Replies
    5
    Views
    712

    What battery and LED setup are you trying to use?...

    What battery and LED setup are you trying to use?

    There isn't much that can be wrong with the speaker other than possibly shorting, but I wouldn't expect 3 speakers to all have that issue (or even...
  21. Replies
    2
    Views
    1,251

    Keep in mind the LED gets very hot. I've built...

    Keep in mind the LED gets very hot. I've built several prototypes of this type of thing (see Space Windu's interview with me or a demo). My main concern with this as a product is that LEDs can get...
  22. Replies
    11
    Views
    1,172

    The solid round tip actually gets pretty good...

    The solid round tip actually gets pretty good illumination from internal reflection. Works better than the solid parabolic. Only thing to do is remove the mirror and it should light up nicely. You...
  23. Replies
    11
    Views
    1,172

    3535 have their problems as well, the light is...

    3535 have their problems as well, the light is more concentrated into smaller spots that are further apart. 5050s work fine. Diffusion is your friend.
  24. Replies
    40
    Views
    6,146

    Nice work. You should always push yourself in...

    Nice work. You should always push yourself in this hobby. If you haven't wasted a part in pursuit of making something new and exciting, you aren't trying hard enough. If you are just screwing...
  25. Replies
    3
    Views
    1,152

    Classic!

    Classic!
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4