Search:

Type: Posts; User: erv

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    103
    Views
    26,009

    Poll: adjust your htemp settings to a higher temperature

    adjust your htemp settings to a higher temperature
  2. Replies
    78
    Views
    7,161

    7.4v to the strips probaby killed them, and...

    7.4v to the strips probaby killed them, and eventually your onboard L1 to L4 drivers. Not sure why you'd apply 7.4V to 5V strips.
    I'd test the invididual drivers with 5mm led, you don't need HB leds...
  3. Replies
    120
    Views
    23,162

    Hey Firebird21 ! long time ! yeah, CFv9 and now...

    Hey Firebird21 ! long time !
    yeah, CFv9 and now CFX (v10) since a couple of month, time flies, still there, growing grey hair ;-)
    Not in this place anymore as I do all the support on fx-sabers...
  4. Replies
    30
    Views
    5,852

    are your still doing this with an RGB accent...

    are your still doing this with an RGB accent connected to the flexiblend signals ? do you use resistors ? Are those voltages from the FoC1-2 and main PWM pads ?
  5. Replies
    30
    Views
    5,852

    having the battery voltage on the CEx output with...

    having the battery voltage on the CEx output with no led attached is *normal*. Same on the onboard driver of the PC or CF (no load = no regulation).
    FJK remarks makes a point for small glitches...
  6. Replies
    30
    Views
    5,852

    from the unwired pics above, the board looks in...

    from the unwired pics above, the board looks in good condition, however, if the board went smoking with the saber off, there's an issue, probably in the wiring. you might want to send me the board...
  7. Replies
    30
    Views
    5,852

    jumping to the discussion :-) among other things,...

    jumping to the discussion :-) among other things, are you sure you wired the CEx with +, channel 1, ground, channel 2
    (if by mistake the ground is on pin 4 that could be it)

    second thing is to...
  8. Replies
    17
    Views
    3,696

    Hi ! A few things - the 2 connected parts are...

    Hi ! A few things
    - the 2 connected parts are meant to be connected. They sometimes move during the reflow due to copper heat attraction.
    - thru hole wiring is not bad per say. I do not see...
  9. Replies
    5
    Views
    1,463

    you're very welcome. I'll add also something...

    you're very welcome. I'll add also something important (mentioned in the NB manual too) : NEVER lower the drive under 80% (820) as a(nother) rule of the thumb.
  10. Replies
    5
    Views
    1,463

    hi there, Erv' here, I've been paged :-) You...

    hi there, Erv' here, I've been paged :-)

    You might have a look to the Nano Biscotte user's manual to learn about the "drive" which applies as well to CFv6 and PC2 FoC channels.

    question #1 :...
  11. Replies
    10
    Views
    1,863

    excellent ! thanks for sharing that tip with us !

    excellent ! thanks for sharing that tip with us !
  12. Replies
    10
    Views
    1,863

    where did you get your drivers initially ? the...

    where did you get your drivers initially ? the ones from silabs work just fine.

    updated the version of RICE for the PCv2,
    the CF version will be updated as well in 5 minutes.
  13. Replies
    10
    Views
    1,863

    either a windows problem : uninstall peripheral,...

    either a windows problem : uninstall peripheral, un install drivers, start over.. (never got that issue on any of my computers though)
    or you have a short in your wiring and the cable cannot be...
  14. Replies
    10
    Views
    1,863

    good point, thanks a lot for posting this....

    good point, thanks a lot for posting this. Actually, I realize a while ago that the time base requires to put 40 to get it on all the time, no 30. I corrected this in the manual (at least for CFV5)...
  15. Replies
    2
    Views
    1,232

    That's correct, 1 space crammed in front of each...

    That's correct, 1 space crammed in front of each line except the comment.
    Javascript had fun with me on that one.

    fixed
    updated version here
    ...
  16. Replies
    132
    Views
    23,841

    this still has to be discussed, but I think I'll...

    this still has to be discussed, but I think I'll just release a new firmware that just not feature the possibility to lock the board/fonts.
    With the board being sold unlocked, there's is no point...
  17. Replies
    132
    Views
    23,841

    since it's a minor error and not a full messup,...

    since it's a minor error and not a full messup,
    a minor clue

    "the most famous" is a sentence totally subjective.

    :)
  18. Replies
    132
    Views
    23,841

    minor error (sorry). Updated Leia picture !

    minor error (sorry). Updated Leia picture !
  19. Replies
    132
    Views
    23,841

    of course, I won't comment anything about the...

    of course, I won't comment anything about the progress and I won't give more clues,
    however I'll just quote what I've posted on fx-sabers for the sake of fun
  20. Replies
    132
    Views
    23,841

    "Crack the PC-L" - a Foreword Greetings sabers...

    "Crack the PC-L" - a Foreword

    Greetings sabers enthusiasts ! It's always a weird experience to build up a "protection" for a device that applies to hobby and DIY. Still, I would say that it's been...
  21. Replies
    31
    Views
    6,348

    honored to have a section in there, very funny...

    honored to have a section in there,
    very funny stuff ! :D
  22. lesson learned, never make a too symmetrical...

    lesson learned, never make a too symmetrical board.
    I'm actually surprised no one has claimed yet the invention of that very RPS ("Reverse Powering System") :wink:
  23. I've almost never left a dead board in the wild,...

    I've almost never left a dead board in the wild, and that' pretty much what Zook is offering too. I stand behind my products, just like I react as fast as possible for bug fixing. That's now public...
  24. Replies
    9
    Views
    2,229

    not all dice have the same current, first thing....

    not all dice have the same current, first thing. So even if you plan to change color with powering off the saber, you'll need to change the led current too. Still, most RGB accept the same average...
  25. Replies
    29
    Views
    10,825

    the tweeter just has 2 pins, it's a speaker. ...

    the tweeter just has 2 pins, it's a speaker.



    from what I read, capacitor is between the 2 positive the speakers. Both have a common ground (obviously).
    A 4.7 uF ceramic looks like the pic...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4