Search:

Type: Posts; User: darth_chasm

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    2,114

    If you are referring to the longer, pre-wired...

    If you are referring to the longer, pre-wired "assembly" then no. It is not representative of all NB v4's. That is a custom board that was designed exclusively for TCSS. The differences between it...
  2. Replies
    1
    Views
    77

    Accent Pixel should do the trick. I personally...

    Accent Pixel should do the trick. I personally would wire it parallel to the blade. It's the diagram that appears above the one you posted here.
  3. Ha!! This is my hometown.

    Ha!! This is my hometown.
  4. Replies
    3
    Views
    259

    Welcome My gut tells me that if there is any...

    Welcome

    My gut tells me that if there is any change it will be negligible. Yeah, we use mirrored blade tips for in hilt leds but in that case the light is pointed directly at the reflective...
  5. Replies
    6
    Views
    299

    Thanks for the kind words guys!

    Thanks for the kind words guys!
  6. Replies
    3
    Views
    207

    Welcome back! Yeah, the hobby has changed quite a...

    Welcome back! Yeah, the hobby has changed quite a bit. Even in the time I've been active it has changed.

    CFX can run on 3.7v now without any hacks. You'll want to go with the high drain 15A cell....
  7. Replies
    6
    Views
    299

    Thanks SS. Long time no speak. Hope you're doing...

    Thanks SS. Long time no speak. Hope you're doing well.
  8. Replies
    1
    Views
    119

    you can charge one

    you can charge one
  9. Replies
    5
    Views
    187

    I think you might need to connect L3 to the...

    I think you might need to connect L3 to the Negative of the connector as well. I may be wrong so if someone knows otherwise please chime in. Also, did you order it set up for neopixel? There's a...
  10. Replies
    6
    Views
    299

    DCLS-006le #1

    I'm sure many have seen it already elsewhere, but TCSS was key in getting this done so I need to post this here as well. This is the refinement of the prototype design from a couple of years ago.
    ...
  11. Replies
    6
    Views
    379

    I've used 6-32 before that have worked ok for...

    I've used 6-32 before that have worked ok for light sword play. IDK, maybe others can chime in on the 4-40. It's just that the nose on those has such a small point of contact.
  12. MHS discs have 2 holes because thats what works...

    MHS discs have 2 holes because thats what works with MHS parts and MHS parts are not the same dimensions as a Graflex. So there is really nothing there making things complicated.

    Have you, by...
  13. Replies
    6
    Views
    379

    Personal preference, I wouldn't use 4-40. Im no...

    Personal preference, I wouldn't use 4-40. Im no engineer so I don't even know where to begin to determine if it is indeed too small. I just wouldn't.

    What kind of use is the saber intended for?...
  14. Replies
    4
    Views
    267

    It can happen and I can say with 98% confidence...

    It can happen and I can say with 98% confidence it's the blade that is slightly out of spec. Simply sand the 2 or so inches of the bottom of the blade. Plug up the end with some paper or cotton to...
  15. That looks really good!

    That looks really good!
  16. Replies
    2
    Views
    216

    Welcome to the addiction :D

    Welcome to the addiction :D
  17. These all incorporate custom chambers with a mix...

    These all incorporate custom chambers with a mix of 3D and other things. All is original though. No pre made stuff...
  18. Replies
    11
    Views
    993

    Congrats. Good job. Looks better than a lot of...

    Congrats. Good job. Looks better than a lot of other firsts, or thirds, or twentieths.

    Now the question is how soon until you make another :p
  19. Replies
    7
    Views
    1,701

    welcome back. Sleeve looks good!

    welcome back. Sleeve looks good!
  20. Replies
    2
    Views
    353

    First things first. Safety Glasses and a...

    First things first. Safety Glasses and a respirator. Not a dust mask a respirator. Quartz dust is very harmful.

    You can use a diamond dremel cutting wheel. Do it under running water to reduce heat...
  21. Replies
    3
    Views
    254

    Very pleased with both Saber Essentials speakers,...

    Very pleased with both Saber Essentials speakers, theyre very loud and good range. 28mm Bass is decent. Not a fan of the premium or the 20mm. Have not used the WOW but have heard good things. But...
  22. Replies
    3
    Views
    254

    From the manual...

    From the manual http://www.plecterlabs.com/shop/article_info.php?articles_id=111

    - Speaker: 4 to 8 ohm.- Audio output Power : 2W max
  23. Replies
    11
    Views
    993

    Yeah it should be fine. If you do want to save...

    Yeah it should be fine. If you do want to save room you can change the drive on the greens to say 980 and skip the resistors. But thats totally up to you.
  24. Replies
    11
    Views
    993

    There's no need to round up on your battery. They...

    There's no need to round up on your battery. They charge to 4.2 but drop to 3.7 very quickly. You can get away with a minimal resistor on the greens or dare I say, skip it and use the drive settings...
  25. Replies
    2
    Views
    342

    I don’t recall ever seeing this done. I think the...

    I don’t recall ever seeing this done. I think the first step is finding out the OD and ID of the stick. From there, you and/or forum members can determine what would or would not work.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4